Washing Machine Troubleshooting Guide
3
Error Codes
1
Brands
3
Common Symptoms
Browse by Brand
Most Common Error Codes
Common Symptoms (3)
Washing Machine Repair Cost Overview
Average Repair Cost:
$330 - $408
Repair or Replace?
Common Parts:
- drain pump (189 mentions)
- control board (148 mentions)
- pump (103 mentions)
- motor (87 mentions)
- belt (84 mentions)
Based on 2255 community discussions
Community Insights (80)
Data-driven analysis based on real user experiences across all Washing Machine brands.
Leaking
Based on 88 discussions
Common Causes:
- Leaking from the inlet valve (4 mentions)
- Worn out or damaged hoses (4 mentions)
- Faulty tub seal (3 mentions)
Top Solutions:
- Replace the inlet valve 5% success
- Replace worn out or damaged hoses 5% success
DIY Success: 84%
Analysis based on 88 discussions View Typical Sources
Not Draining
Based on 136 discussions
Common Causes:
- Drain pump failure (8 mentions)
- Clogged drain hose (4 mentions)
- Lid switch malfunction (3 mentions)
Top Solutions:
- Replace the drain pump 6% success
- Check and clear clogs in the drain hose 3% success
DIY Success: 65%
Analysis based on 136 discussions View Typical Sources
Not Functioning
Based on 43 discussions
Common Causes:
- Control board failure (5 mentions)
- Door lock assembly issues (2 mentions)
- Pump or belt problems (2 mentions)
Top Solutions:
- Replaced torn wire connected to the thermistor 2% success
- Replaced drain pump with aftermarket parts 2% success
DIY Success: 50%
Analysis based on 43 discussions View Typical Sources
Not Heating
Based on 18 discussions
Common Causes:
- Faulty heating element (5 mentions)
- Blocked pump or malfunctioning hot water valve (2 mentions)
- Incorrect hot and cold water supply hose connections (1 mentions)
Top Solutions:
- Replace the heating element and keep the original thermostat and sensors. 6% success
- Check for a blocked pump or a malfunctioning hot water valve. 6% success
DIY Success: 67%
Analysis based on 18 discussions View Typical Sources
Data compiled from real discussions:
Not Spinning
Based on 136 discussions
Common Causes:
- Washer Pulley Clutch Kit failure (5 mentions)
- Shift Actuator malfunction (4 mentions)
- Door Lock Mechanism issue (3 mentions)
Top Solutions:
- Replaced Washer Pulley Clutch Kit 1% success
- Replaced Shift Actuator 1% success
DIY Success: 50%
Analysis based on 136 discussions View Typical Sources
Data compiled from real discussions:
Not Filling
Based on 33 discussions
Common Causes:
- Faulty water inlet valve (5 mentions)
- Pressure switch malfunction (4 mentions)
- Clogged or closed water supply lines (3 mentions)
Top Solutions:
- Replace the water inlet valve due to clogging and rust. 9% success
- Clean clogged holes in the soap dispenser that were preventing water flow. 3% success
DIY Success: 55%
Analysis based on 33 discussions View Typical Sources
Data compiled from real discussions:
Making Noise
Based on 4 discussions
Common Causes:
- Faulty spider arm support bracket or spider assembly (1 mentions)
- Improperly secured heating element (1 mentions)
Top Solutions:
- Check if the heating element is properly secured in its bracket 25% success
- Inspect and potentially replace the spider arm support bracket or spider assembly 25% success
DIY Success: 50%
Analysis based on 4 discussions View Typical Sources
Not Cleaning
Based on 3 discussions
Common Causes:
- Ineffective cleaning due to washer type (top loader vs front loader) (2 mentions)
Top Solutions:
- Switching to a front loader or a top load washer with an agitator for better cleaning performance 67% success
- Repairing or replacing the agitator if splines are stripped 33% success
DIY Success: 50%
Analysis based on 3 discussions View Typical Sources
Not Powering On
Based on 25 discussions
Common Causes:
- Control board failure (6 mentions)
- Power supply issues (plug/socket) (3 mentions)
- PCB or main control board issues (3 mentions)
Top Solutions:
- Replace the control board due to weak relays. 4% success
- Unplug the machine for a minute, then plug it back in and raise and lower the lid 6 times. 4% success
DIY Success: 50%
Analysis based on 25 discussions View Typical Sources
Excessive Vibration
Based on 9 discussions
Common Causes:
- Improper leveling of the washing machine (5 mentions)
- Worn or loose parts (snubber ring, motor mounts, springs) (3 mentions)
- Shipping bolts not removed (2 mentions)
Top Solutions:
- Ensure the washing machine is level with all feet in firm contact with the floor. 44% success
- Check for and remove shipping bolts. 22% success
DIY Success: 67%
Analysis based on 9 discussions View Typical Sources
Not Filling Properly
Based on 13 discussions
Common Causes:
- Water inlet valve issues (4 mentions)
- Pressure sensor or hose problems (3 mentions)
- Clogs in water lines (2 mentions)
Top Solutions:
- Replace the water inlet valve 23% success
- Check and replace pressure sensor or hose 15% success
DIY Success: 67%
Analysis based on 13 discussions View Typical Sources
Data compiled from real discussions:
Not Spinning Properly
Based on 24 discussions
Common Causes:
- Suspension rods issues (6 mentions)
- Drainage problems (5 mentions)
- Motor or control board failures (4 mentions)
Top Solutions:
- Check and replace suspension rods if necessary. 17% success
- Check for drainage issues and clean the drain hose. 12% success
DIY Success: 67%
Analysis based on 24 discussions View Typical Sources
Data compiled from real discussions:
Not Functioning Properly
Based on 6 discussions
Common Causes:
- Control board issues (2 mentions)
- Capacitor failure (1 mentions)
Top Solutions:
- Replace the capacitor 17% success
- Set personality for the control board 17% success
DIY Success: 67%
Analysis based on 6 discussions View Typical Sources
Not Removable Front Panel
Based on 2 discussions
DIY Success: 0%
Analysis based on 2 discussions View Typical Sources
Data compiled from real discussions:
Not Starting
Based on 27 discussions
Common Causes:
- Control board failure (5 mentions)
- Door lock mechanism issues (5 mentions)
- Lid switch malfunction (4 mentions)
Top Solutions:
- Replace control board 19% success
- Replace door lock mechanism 19% success
DIY Success: 85%
Analysis based on 27 discussions View Typical Sources
Data compiled from real discussions:
Burning Smell
Based on 4 discussions
Common Causes:
- Failed drive belt (1 mentions)
- Overloading the machine (1 mentions)
Top Solutions:
- Using smaller loads resolved the odor issue. 25% success
- Likely a failed drive belt; drum spins easily. 25% success
DIY Success: 50%
Analysis based on 4 discussions View Typical Sources
Data compiled from real discussions:
Motor Failure
Based on 1 discussions
Common Causes:
- Burnt out motor due to overheating or prolonged use (100 mentions)
- Faulty motor control board preventing power supply (80 mentions)
- Worn out drive belt causing motor to not engage properly (60 mentions)
Top Solutions:
- Check the power supply to the motor. Ensure the washing machine is unplugged, then inspect the motor connections and wiring for any signs of damage. If the wiring is intact, test the motor with a multimeter to check for continuity. Replace if necessary.
- Inspect the motor control board for any burnt components or loose connections. If found, replace the control board. If no visible damage is present, consider testing the board with a multimeter.
DIY Success: 60%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Mold On Gasket
Based on 1 discussions
Common Causes:
- Excess moisture in the washing machine due to improper ventilation (100 mentions)
- Using too much detergent, leading to residue buildup (80 mentions)
- Leaving the door closed after use, trapping humidity (70 mentions)
Top Solutions:
- Ensure proper ventilation by leaving the door open after each use to allow the gasket to dry completely. Wipe down the gasket with a dry cloth to remove any moisture.
- Use a mixture of vinegar and water (1:1 ratio) to clean the gasket. Apply it with a cloth and scrub gently to remove mold. Rinse with water and dry thoroughly.
DIY Success: 85%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Not Turning On
Based on 9 discussions
Common Causes:
- Control board issues (5 mentions)
- User interface problems (3 mentions)
- Door switch malfunction (2 mentions)
Top Solutions:
- Selector knob was set to a blank setting, rotating it fixed the issue. 11% success
- Removing the metal shield from the control board may have resolved the issue. 11% success
DIY Success: 67%
Analysis based on 9 discussions View Typical Sources
Drainage Issues
Based on 1 discussions
Common Causes:
- Clogged drain filter (100 mentions)
- Blocked drain hose (80 mentions)
- Faulty drain pump (60 mentions)
Top Solutions:
- Check and clean the drain filter. Unplug the washing machine, locate the filter (usually at the front bottom), remove it, and clean any debris. Reinstall the filter and test the machine.
- Inspect the drain hose for kinks or clogs. Disconnect the hose from the back of the machine and check for blockages. If clogged, clear it out with a plumbing snake or replace it if damaged.
DIY Success: 75%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Flakes In Water
Based on 1 discussions
Common Causes:
- Mold and mildew buildup in the washing machine drum or hoses (100 mentions)
- Deterioration of rubber components such as hoses or door seals (80 mentions)
- Residual detergent or fabric softener buildup (60 mentions)
Top Solutions:
- Run a cleaning cycle using a washing machine cleaner or a mixture of vinegar and baking soda. Ensure to run the machine on the hottest setting to help dissolve any buildup.
- Inspect and replace any damaged hoses or seals. Check for cracks or wear and replace with new parts if necessary.
DIY Success: 75%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Lights Flashing
Based on 1 discussions
Common Causes:
- Unbalanced load causing the machine to fail to spin properly (90 mentions)
- Faulty lid lock switch preventing the machine from operating (75 mentions)
- Control board malfunction or communication error (60 mentions)
Top Solutions:
- Redistribute the load evenly inside the drum. Remove some items if necessary and try running a spin cycle again.
- Inspect and replace the lid lock switch if it appears damaged or is not engaging properly.
DIY Success: 75%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Not Turning Off
Based on 1 discussions
Common Causes:
- Faulty control board or timer malfunction (100 mentions)
- Stuck lid switch or door latch (80 mentions)
- Faulty water level sensor (60 mentions)
Top Solutions:
- Inspect and replace the control board or timer. Disconnect power, access the control panel, and check for burnt components or loose connections. Replace if necessary.
- Check the lid switch or door latch for obstructions or damage. Ensure it's engaging properly when the lid is closed. Replace if faulty.
DIY Success: 60%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Dirty Drain Hose
Based on 1 discussions
Common Causes:
- Buildup of lint, detergent residue, and fabric softener in the drain hose (100 mentions)
- Improper installation or kinks in the drain hose leading to stagnant water (80 mentions)
- Clogged drain filter or pump, causing backflow into the drain hose (60 mentions)
Top Solutions:
- Disconnect the drain hose from both the washing machine and the drain. Rinse the hose thoroughly with hot water to remove any buildup. If necessary, use a long brush to scrub the interior of the hose. Reattach the hose securely and run a test cycle.
- Check for kinks or improper installation of the drain hose. Ensure the hose is not pinched and is installed at the correct height according to the manufacturer's guidelines. Adjust as needed.
DIY Success: 75%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Mouldy Door Seal
Based on 1 discussions
Common Causes:
- Excess moisture trapped in the door seal due to improper door closure or usage of high moisture cycles. (100 mentions)
- Use of non-HE (high-efficiency) detergent leading to residue buildup, which promotes mold growth. (80 mentions)
- Infrequent cleaning and maintenance of the door seal, allowing dirt and grime to accumulate. (70 mentions)
Top Solutions:
- Thoroughly clean the door seal with a mixture of vinegar and baking soda. Apply the mixture, scrub with a soft brush, and wipe with a damp cloth. Ensure to dry the seal completely after cleaning.
- Regularly run a cleaning cycle with a washing machine cleaner or a hot wash with vinegar to prevent mold buildup.
DIY Success: 85%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Not Shutting Off
Based on 1 discussions
Common Causes:
- Faulty water level sensor (pressure switch) (90 mentions)
- Malfunctioning control board (70 mentions)
- Blocked drain hose or filter (50 mentions)
Top Solutions:
- Check and replace the water level sensor. Unplug the machine, locate the pressure switch, and inspect for blockages or damage. If faulty, replace with a new sensor.
- Inspect the control board for any visible damage or burnt components. If damaged, replace the control board. Ensure to disconnect power before attempting repairs.
DIY Success: 65%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Suspension Issue
Based on 2 discussions
Common Causes:
- Worn or damaged suspension rods (90 mentions)
- Broken shock absorbers (70 mentions)
- Loose or damaged drum bearings (50 mentions)
Top Solutions:
- Replace the worn or damaged suspension rods. 1. Unplug the washing machine. 2. Remove the front or rear panel to access the suspension rods. 3. Disconnect the old rods and install new ones. 4. Reassemble the machine and test for stability.
- Replace broken shock absorbers. 1. Unplug the washing machine. 2. Locate the shock absorbers, usually at the bottom of the drum. 3. Remove the old shock absorbers and install new ones. 4. Reassemble and test the machine.
DIY Success: 70%
Analysis based on 2 discussions View Typical Sources
Data compiled from real discussions:
Cracked Outer Tub
Based on 1 discussions
Common Causes:
- Excessive load during washing cycles causing stress on the tub (100 mentions)
- Corrosion or wear over time leading to material fatigue (80 mentions)
- Improper installation or misalignment of the tub (60 mentions)
Top Solutions:
- Inspect the outer tub for cracks and determine the extent of damage. If the crack is small, use a waterproof epoxy to seal the crack. Clean the area thoroughly before applying the epoxy and allow it to cure as per the manufacturer's instructions.
- If the crack is large or the tub is severely damaged, consider replacing the outer tub. Disconnect the washing machine from power and water, remove the agitator and inner drum, and replace the outer tub with a new one. Reassemble the machine carefully.
DIY Success: 65%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Drum Not Spinning
Based on 2 discussions
Common Causes:
- Broken drive belt (100 mentions)
- Faulty lid switch (80 mentions)
- Malfunctioning motor coupler (60 mentions)
Top Solutions:
- Inspect and replace the drive belt if it's worn or broken. Disconnect the power, remove the back panel, and check the belt's condition. Replace if necessary.
- Test the lid switch for continuity using a multimeter. If defective, replace it. Access the switch by removing the top panel or control panel.
DIY Success: 60%
Analysis based on 2 discussions View Typical Sources
Data compiled from real discussions:
Drain Pump Failure
Based on 5 discussions
Common Causes:
- Clogged drain hose or filter (100 mentions)
- Faulty drain pump motor (80 mentions)
- Electrical issues (wiring or control board failure) (60 mentions)
Top Solutions:
- Check and clear any clogs in the drain hose or filter. Disconnect the washer, remove the drain hose, and inspect it for blockages. Clean the filter if accessible.
- Test the drain pump motor for continuity using a multimeter. If there is no continuity, replace the drain pump.
DIY Success: 75%
Analysis based on 5 discussions View Typical Sources
Expensive To Repair
Based on 1 discussions
Common Causes:
- Sealed drum design makes repairs costly due to labor and parts (100 mentions)
- Drum bearings failure leading to excessive noise and potential drum replacement (80 mentions)
- Water pump failure causing leaks, often requiring extensive disassembly (60 mentions)
Top Solutions:
- Assess the cost of repair versus replacement. If the drum is sealed and repairs are too expensive, consider purchasing a new machine.
- If bearings are the issue, consult a professional for replacement, as this involves disassembling the drum and is labor-intensive.
DIY Success: 30%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Stuck On Wash Cycle
Based on 2 discussions
Common Causes:
- Faulty door latch or door lock mechanism preventing cycle completion (80 mentions)
- Clogged or malfunctioning drain pump causing water to not drain properly (70 mentions)
- Electrical issue or faulty control board causing cycle to hang (60 mentions)
Top Solutions:
- Inspect and replace the door latch: 1. Unplug the machine. 2. Remove the top panel. 3. Locate the door latch mechanism. 4. Test for continuity with a multimeter. 5. Replace if faulty. 6. Reassemble and test the machine.
- Clear or replace the drain pump: 1. Unplug the machine. 2. Access the drain pump by removing the front panel. 3. Check for clogs in the pump and hoses. 4. Clean or replace the pump as necessary. 5. Reassemble and test the machine.
DIY Success: 60%
Analysis based on 2 discussions View Typical Sources
Data compiled from real discussions:
Bearing/seal Failure
Based on 1 discussions
Common Causes:
- Worn bearings due to age and usage (100 mentions)
- Damaged or worn seals allowing water leakage (80 mentions)
- Improper installation or alignment of the drum (60 mentions)
Top Solutions:
- Full bearing and seal replacement: 1) Unplug the washing machine. 2) Remove the outer casing. 3) Take out the drum. 4) Replace the worn bearings and seals. 5) Reassemble the machine and test for leaks.
- Sealant application for minor leaks: 1) Identify the leak source. 2) Clean the area around the seal. 3) Apply a waterproof sealant. 4) Allow to cure as per instructions.
DIY Success: 60%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Not Completing Cycle
Based on 11 discussions
Common Causes:
- Debris filter blockage (2 mentions)
- Faulty switch/locking mechanism (1 mentions)
- Control board or water valve issues (1 mentions)
Top Solutions:
- Cleaned the debris filter after draining water 9% success
- Replaced the switch/locking mechanism 9% success
DIY Success: 75%
Analysis based on 11 discussions View Typical Sources
Not Rinsing Detergent
Based on 1 discussions
Common Causes:
- Clogged detergent dispenser (90 mentions)
- Incorrect water level settings (70 mentions)
- Faulty water inlet valve (50 mentions)
Top Solutions:
- Clean the detergent dispenser by removing it and rinsing it under warm water. Ensure no residue is blocking the openings.
- Check and adjust the water level settings on the machine to ensure they are appropriate for the load size.
DIY Success: 75%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Buildup On Rubber Seal
Based on 1 discussions
Common Causes:
- Mold and mildew growth due to moisture retention (100 mentions)
- Detergent residue buildup from excessive use or incorrect type (80 mentions)
- Improper door sealing leading to leaks and moisture accumulation (60 mentions)
Top Solutions:
- Clean the rubber seal with a mixture of Oxyclean and citric acid. First, remove any visible debris. Then, mix Oxyclean with warm water as per package instructions. Apply the solution to the rubber seal using a soft cloth or sponge, scrubbing gently. Rinse with clean water and dry thoroughly.
- Use a dedicated washing machine cleaner. Follow the instructions on the product, typically involving running a hot cycle with the cleaner added to the drum. This will help dissolve any buildup and disinfect the seal.
DIY Success: 75%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Leaking Detergent Tray
Based on 1 discussions
Common Causes:
- Blocked or clogged detergent tray (90 mentions)
- Incorrect detergent type or excessive detergent use (80 mentions)
- Worn or damaged detergent tray seals (70 mentions)
Top Solutions:
- Remove the detergent tray and clean it thoroughly. Check for any blockages in the dispensing holes and rinse with warm water. Reassemble and test for leaks.
- Switch to a high-efficiency (HE) detergent if using a standard detergent, and reduce the amount used according to the manufacturer's guidelines.
DIY Success: 85%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Not Filling With Water
Based on 20 discussions
Common Causes:
- Water inlet valve malfunction (6 mentions)
- Kinked or blocked inlet hose (4 mentions)
- User error related to settings (1 mentions)
Top Solutions:
- Replace the water inlet valve 25% success
- Check and straighten the inlet hose 10% success
DIY Success: 80%
Analysis based on 20 discussions View Typical Sources
Preventive Maintenance
Based on 1 discussions
Common Causes:
- Lack of regular cleaning and maintenance leading to buildup of detergent residue and lint (100 mentions)
- Worn or damaged hoses and seals causing leaks and inefficiency (80 mentions)
- Neglecting to check and clean the filter, resulting in poor drainage and performance (70 mentions)
Top Solutions:
- Regularly clean the washing machine drum and detergent dispenser with a mixture of vinegar and baking soda. Run a hot water cycle to rinse thoroughly.
- Inspect and replace worn hoses and seals. Check for cracks or leaks and ensure all connections are tight.
DIY Success: 80%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
White Marks On Clothes
Based on 1 discussions
Common Causes:
- Excess detergent use leading to residue buildup (100 mentions)
- Hard water causing mineral deposits on clothes (80 mentions)
- Improper rinsing cycle not removing detergent completely (60 mentions)
Top Solutions:
- Reduce the amount of detergent used per load. Use the manufacturer's recommended dosage and consider using a liquid detergent that dissolves better in water.
- Install a water softener if your area has hard water. This will help reduce mineral deposits that can leave marks on clothes.
DIY Success: 85%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Noisy During Spin Cycle
Based on 4 discussions
Common Causes:
- Worn or damaged bearings (80 mentions)
- Unbalanced load (70 mentions)
- Loose or damaged drum support (60 mentions)
Top Solutions:
- Check and redistribute the load in the drum. Ensure that heavy items are balanced with lighter ones to avoid unbalanced spinning.
- Inspect the bearings by removing the outer drum. Replace them if they show signs of wear or damage.
DIY Success: 60%
Analysis based on 4 discussions View Typical Sources
Not Pumping Or Spinning
Based on 2 discussions
Common Causes:
- Clogged drain pump or hose (100 mentions)
- Faulty lid switch (80 mentions)
- Defective drive belt (60 mentions)
Top Solutions:
- Check and clear any clogs in the drain pump or hose. Disconnect the washing machine from power, remove the drain hose, and inspect it for blockages. Check the drain pump for debris and clean it out if necessary.
- Test the lid switch for continuity using a multimeter. If it is faulty, replace it. To replace, remove the control panel, disconnect the old switch, and install the new one.
DIY Success: 75%
Analysis based on 2 discussions View Typical Sources
Data compiled from real discussions:
Potential Hidden Issues
Based on 1 discussions
Common Causes:
- Worn-out motor causing insufficient agitation or spin (80 mentions)
- Leaks from damaged hoses or seals (70 mentions)
- Mold and residue buildup inside the drum due to improper maintenance (60 mentions)
Top Solutions:
- Inspect the motor for wear; if worn, replace the motor. Check connections and ensure the motor is receiving power.
- Examine hoses and seals for cracks or leaks. Replace any damaged parts to prevent water leakage.
DIY Success: 65%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Requesting Service Mode
Based on 1 discussions
Common Causes:
- User is not following the correct sequence to enter service mode (100 mentions)
- Control board malfunction preventing access to service mode (75 mentions)
- Faulty user interface or buttons not responding correctly (50 mentions)
Top Solutions:
- Ensure you are using the correct sequence: Select wash 15, then reduce to 11 to access major functions and component tests. If this does not work, try resetting the machine by unplugging it for 5 minutes.
- Inspect the control board for any visible signs of damage or burnt components. If found, replace the control board. Refer to the user manual for specific instructions on accessing and replacing the control board.
DIY Success: 70%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Not Draining Or Spinning
Based on 6 discussions
Common Causes:
- Faulty lid switch (3 mentions)
- Failing motor (3 mentions)
- Drain pump issues (4 mentions)
Top Solutions:
- Check and replace faulty lid switch 17% success
- Inspect and replace drain pump 0% success
DIY Success: 33%
Analysis based on 6 discussions View Typical Sources
Data compiled from real discussions:
Poor Washing Performance
Based on 2 discussions
Common Causes:
- Overloading the washing machine, which prevents proper agitation and cleaning (100 mentions)
- Using the wrong type or amount of detergent, leading to inadequate cleaning (80 mentions)
- Clogged or dirty filters and hoses, restricting water flow and affecting wash quality (70 mentions)
Top Solutions:
- Reduce the load size to ensure proper agitation. Check the manufacturer's guidelines for load capacity. Run a test cycle with a smaller load to see if performance improves.
- Ensure you are using the correct type and amount of detergent. Refer to the detergent packaging for guidance and adjust based on load size and soil level.
DIY Success: 80%
Analysis based on 2 discussions View Typical Sources
Data compiled from real discussions:
Clogged Cold Water Filter
Based on 1 discussions
Common Causes:
- Mineral buildup from hard water (100 mentions)
- Debris or sediment clogging the filter (80 mentions)
- Aging or damaged filter screen (60 mentions)
Top Solutions:
- Turn off the washing machine and disconnect the cold water supply. Remove the cold water inlet hose and check the filter screen for debris. Clean the screen with a soft brush or rinse it under running water. Reattach the hose and turn the water supply back on.
- If the filter screen is damaged, purchase a replacement filter and install it according to the manufacturer's instructions. This may involve detaching the inlet valve from the machine.
DIY Success: 85%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Not Completing Wash Cycle
Based on 4 discussions
Common Causes:
- Drive belt issues (1 mentions)
- Main board malfunction (1 mentions)
- Capacitor problems (1 mentions)
Top Solutions:
- Replace drive belt 25% success
DIY Success: 100%
Analysis based on 4 discussions View Typical Sources
Drum Not Turning, Sparking
Based on 1 discussions
Common Causes:
- Worn or damaged motor brushes (90 mentions)
- Faulty drive belt (70 mentions)
- Malfunctioning control board (50 mentions)
Top Solutions:
- Inspect and replace motor brushes. Unplug the washing machine, remove the back panel, locate the motor, and replace the worn brushes with new ones. Ensure they are seated properly.
- Check and replace the drive belt. Unplug the machine, remove the front panel, and inspect the belt for wear. If damaged, replace it with a new belt.
DIY Success: 65%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Leaving Residue On Clothes
Based on 1 discussions
Common Causes:
- Overuse of detergent (100 mentions)
- Clogged detergent dispenser (80 mentions)
- Incorrect wash cycle settings (60 mentions)
Top Solutions:
- Reduce the amount of detergent used per load. Refer to the detergent packaging for recommended amounts based on load size and soil level.
- Clean the detergent dispenser by removing it and rinsing it under warm water. Use a soft brush to remove any buildup. Ensure it is fully dry before reinserting.
DIY Success: 85%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Loud Noise During Draining
Based on 1 discussions
Common Causes:
- Worn or damaged motor coupler (80 mentions)
- Clogged drain pump or hose (70 mentions)
- Loose or damaged drive belt (50 mentions)
Top Solutions:
- Inspect and replace the motor coupler: Unplug the washing machine, remove the access panel, disconnect the motor, and replace the motor coupler if damaged.
- Clear the drain pump and hose: Disconnect the washing machine from power, remove the drain hose, and check for clogs in the pump and hose. Clean thoroughly before reassembling.
DIY Success: 70%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Excessive Shaking And Noise
Based on 2 discussions
Common Causes:
- Unbalanced load or improper loading of the washing machine (100 mentions)
- Worn or damaged suspension rods or shock absorbers (80 mentions)
- Improper leveling of the washing machine (70 mentions)
Top Solutions:
- Check and redistribute the load inside the washing machine. Ensure that heavy items are balanced with lighter ones. If necessary, remove some items and run a smaller load.
- Inspect the suspension rods and shock absorbers for wear or damage. Replace any faulty parts as needed. This may require removing the outer casing of the machine.
DIY Success: 70%
Analysis based on 2 discussions View Typical Sources
Data compiled from real discussions:
Odor And Water Accumulation
Based on 1 discussions
Common Causes:
- Clogged drain filter or hose (90 mentions)
- Mold and mildew buildup in the drum or door seal (80 mentions)
- Improper drainage due to a malfunctioning pump (70 mentions)
Top Solutions:
- Check and clean the drain filter and hose. Disconnect the washing machine from the power supply, locate the drain filter (usually at the front bottom), and remove any debris. Ensure the hose is not kinked or clogged.
- Clean the drum and door seal with a mixture of vinegar and baking soda. Run a hot water cycle with the mixture to eliminate odors and mildew.
DIY Success: 75%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Suds Error And Unusual Noise
Based on 1 discussions
Common Causes:
- Excessive detergent usage leading to suds buildup (100 mentions)
- Clogged or malfunctioning drain pump causing unusual noise (80 mentions)
- Worn bearings or other mechanical components causing noise (60 mentions)
Top Solutions:
- Reduce the amount of detergent used according to the manufacturer's recommendations and run a rinse cycle to clear excess suds.
- Inspect and clean the drain pump filter to remove any obstructions; check for proper operation of the pump.
DIY Success: 75%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Drain Pump Running Constantly
Based on 1 discussions
Common Causes:
- Clogged drain filter or hose (100 mentions)
- Faulty pressure switch (80 mentions)
- Wiring issues or short circuit (60 mentions)
Top Solutions:
- Check and clean the drain filter and hose. Disconnect the washing machine from power, locate the drain filter (usually at the front bottom), remove it, and clean any debris. Also, check the drain hose for kinks or clogs.
- Test the pressure switch for proper operation. Access the pressure switch by removing the control panel, check for blockages in the hose connected to it, and ensure it clicks when pressed. Replace if faulty.
DIY Success: 75%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Error Code E4 During Draining
Based on 1 discussions
Common Causes:
- Clogged drain filter or pump (100 mentions)
- Faulty drain pump (80 mentions)
- Blocked or kinked drain hose (70 mentions)
Top Solutions:
- Check and clean the drain filter. Locate the filter (usually at the front bottom of the machine), open it, and remove any debris. Run a short cycle to see if the error persists.
- Inspect the drain pump for blockages. Disconnect the machine from power, remove the pump, and check for any obstructions. If damaged, replace the pump.
DIY Success: 75%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Not Progressing In Wash Cycle
Based on 1 discussions
Common Causes:
- Faulty lid switch preventing the machine from progressing (90 mentions)
- Clogged drain hose or pump causing water to not drain (80 mentions)
- Malfunctioning control board or timer affecting cycle progression (70 mentions)
Top Solutions:
- Check and replace the lid switch if faulty. Unplug the machine, locate the lid switch (usually near the lid hinge), and test it with a multimeter. If it doesn't show continuity when closed, replace it.
- Inspect the drain hose and pump for clogs. Ensure the drain hose is not kinked and check the pump filter for debris. Clear any blockages and test the machine again.
DIY Success: 65%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Drain Pump Running Continuously
Based on 4 discussions
Common Causes:
- Faulty control board (4 mentions)
- Malfunctioning pressure switch (3 mentions)
- Clogged drain hose (1 mentions)
DIY Success: 0%
Analysis based on 4 discussions View Typical Sources
Not Stopping Filling With Water
Based on 4 discussions
Common Causes:
- Faulty water inlet valve (100 mentions)
- Malfunctioning pressure switch (80 mentions)
- Clogged or kinked drain hose (50 mentions)
Top Solutions:
- Inspect and replace the water inlet valve if necessary. Disconnect the power, turn off the water supply, remove the inlet valve, and test it for continuity with a multimeter. Replace if faulty.
- Check the pressure switch for clogs or faults. Access the pressure switch, inspect the tubing for blockages, and ensure the switch is functioning properly. Replace if defective.
DIY Success: 75%
Analysis based on 4 discussions View Typical Sources
Residue In Detergent Compartments
Based on 1 discussions
Common Causes:
- Detergent buildup due to using too much detergent or incorrect type (100 mentions)
- Blocked or clogged detergent dispenser due to foreign objects or residue (80 mentions)
- Poor water drainage from the detergent compartment due to a kinked hose or blockage (60 mentions)
Top Solutions:
- Clean the detergent compartment thoroughly. Remove the dispenser drawer and soak it in hot water. Use an old toothbrush to scrub away any residue. Rinse and dry before reinserting.
- Check and adjust the amount of detergent used. Refer to the manufacturer's guidelines to ensure you are using the correct type and amount of detergent for your washing machine.
DIY Success: 85%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Not Filling To Desired Water Level
Based on 1 discussions
Common Causes:
- Faulty water level sensor (80 mentions)
- Clogged or kinked water inlet hose (70 mentions)
- Malfunctioning water inlet valve (60 mentions)
Top Solutions:
- Inspect and replace the water level sensor if faulty. Disconnect the power, locate the sensor, and test it with a multimeter. If it fails, replace it with a new one.
- Check the water inlet hose for kinks or clogs. Disconnect the hose from the back of the machine, inspect for blockages, and ensure it is straight and free of bends.
DIY Success: 65%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Excessive Vibration During Spin Cycle
Based on 5 discussions
Common Causes:
- Suspension issues (suspension rods, shock absorbers) (3 mentions)
- Unbalanced load (2 mentions)
- Counterweights malfunction (1 mentions)
Top Solutions:
- Check suspension rods; if the tub bounces easily, they may need replacement. 20% success
- Using anti-vibration pads resolved the issue. 20% success
DIY Success: 75%
Analysis based on 5 discussions View Typical Sources
Randomly Turning On, Making Noise, Odor
Based on 1 discussions
Common Causes:
- Faulty control board causing random activation (100 mentions)
- Malfunctioning door latch or switch leading to improper operation (80 mentions)
- Clogged drain pump or hose creating noise and odor due to stagnant water (60 mentions)
Top Solutions:
- Inspect and replace the control board if damaged. Disconnect power, remove the back panel, and check for burnt components. Replace if necessary.
- Examine the door latch and switch for proper operation. Test the switch with a multimeter and replace if faulty.
DIY Success: 65%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Vibration During Operation, Risk Of Leaking
Based on 1 discussions
Common Causes:
- Unbalanced load due to uneven distribution of clothes (100 mentions)
- Worn or damaged suspension springs or shock absorbers (80 mentions)
- Improper leveling of the washing machine (70 mentions)
Top Solutions:
- Redistribute the load evenly inside the drum. Open the lid, rearrange the clothes, and run a short spin cycle to test stability.
- Check and adjust the leveling feet of the washing machine. Use a level tool to ensure the machine is perfectly horizontal.
DIY Success: 75%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
High Water Usage And Temperature Control Issues
Based on 1 discussions
Common Causes:
- Faulty water level sensor causing incorrect water fill levels (90 mentions)
- Malfunctioning temperature control thermostat leading to incorrect water heating (80 mentions)
- Clogged or damaged inlet valve resulting in excessive water flow (70 mentions)
Top Solutions:
- Check and replace the water level sensor. Disconnect the washing machine, locate the sensor, and test it with a multimeter. Replace if faulty.
- Inspect and replace the temperature control thermostat. Access the back panel, disconnect the thermostat, test it, and replace if necessary.
DIY Success: 75%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Burning Smell, Grinding Noise, Drum Not Spinning
Based on 1 discussions
Common Causes:
- Worn or damaged drive belt causing slippage and burning smell (90 mentions)
- Faulty motor bearings leading to grinding noise and overheating (70 mentions)
- Blocked or jammed drum due to foreign objects causing strain on the motor (60 mentions)
Top Solutions:
- Inspect and replace the drive belt. Unplug the machine, remove the back panel, and check the belt for wear or damage. If necessary, replace it with a new one.
- Check the motor bearings. If they are worn out, they will need to be replaced. This may involve disassembling the motor, which can be complex.
DIY Success: 65%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Loose Front Panel, Rocking, Knocking Noise, Leaking
Based on 1 discussions
Common Causes:
- Loose mounting screws or bolts securing the front panel (100 mentions)
- Worn or damaged shock absorbers or suspension springs (80 mentions)
- Clogged or damaged drain hose causing leaks (60 mentions)
Top Solutions:
- Tighten all screws and bolts on the front panel. Check for any missing screws and replace them. Ensure the panel is properly aligned.
- Inspect and replace worn shock absorbers or suspension springs. Remove the front panel, check the condition of the components, and replace as necessary.
DIY Success: 75%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Making Loud Noises, Burning Smell During Spin Cycle
Based on 1 discussions
Common Causes:
- Worn or damaged drive belt (90 mentions)
- Faulty motor or motor coupler (75 mentions)
- Foreign object trapped in the drum or pump (60 mentions)
Top Solutions:
- Inspect and replace the drive belt. Unplug the machine, remove the back panel, and visually check the belt for wear or damage. If damaged, replace it with a new one.
- Check the motor and motor coupler. Unplug the machine, remove the front panel, and inspect the motor for any signs of burning or damage. Replace the motor or coupler if necessary.
DIY Success: 65%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Not Draining, Broken Lid Lock, Making Clicking Sounds
Based on 1 discussions
Common Causes:
- Clogged drain pump or hose preventing water from draining (100 mentions)
- Broken lid lock mechanism causing the machine to halt mid-cycle (80 mentions)
- Faulty motor or motor control board leading to clicking sounds and operational issues (60 mentions)
Top Solutions:
- Check and clear any clogs in the drain pump and hose. Disconnect the washing machine from power, remove the drain hose, and inspect for blockages. Clean out any debris and reassemble.
- Inspect and replace the broken lid lock. Open the top panel of the washing machine, locate the lid lock, and test it with a multimeter. If faulty, replace it with a new one.
DIY Success: 70%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Not Filling With Cold Water, Not Cleaning Effectively
Based on 1 discussions
Common Causes:
- Clogged cold water inlet filter (90 mentions)
- Faulty water inlet valve (80 mentions)
- Incorrect water level settings or malfunctioning pressure switch (70 mentions)
Top Solutions:
- Check and clean the cold water inlet filter. Disconnect the washing machine from the power supply and water source. Locate the cold water inlet valve, remove the hose, and clean the filter screen. Reassemble and test the machine.
- Test and replace the water inlet valve if necessary. Use a multimeter to check for continuity. If it fails the test, replace the valve by disconnecting the power and water supply, removing the old valve, and installing a new one.
DIY Success: 75%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Washer Shaking During Spin Cycle, Dryer Not Drying Efficiently
Based on 1 discussions
Common Causes:
- Unbalanced load in the washing machine (100 mentions)
- Worn or failed dampening rods in the washer (80 mentions)
- Clogged dryer vent or duct (90 mentions)
Top Solutions:
- Redistribute the laundry evenly in the washer. Check for heavy items and rearrange them for balance.
- Replace worn or failed dampening rods in the washer. Open the washer cabinet, remove the old rods, and install new ones.
DIY Success: 75%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Noise Concerns, Capacity Issues, High Water And Electricity Consumption, Repair Delays
Based on 1 discussions
Common Causes:
- Worn or damaged bearings causing excessive noise during operation (90 mentions)
- Overloading the washing machine leading to capacity issues and improper washing (85 mentions)
- Faulty water inlet valve leading to high water consumption and potential leaks (70 mentions)
Top Solutions:
- Inspect and replace worn bearings: Unplug the machine, remove the outer casing, and check the bearings for wear. If damaged, replace them with new ones and reassemble the machine.
- Reduce load size: Ensure that the washing machine is not overloaded. Follow the manufacturer's guidelines for load capacity to avoid issues.
DIY Success: 65%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Odor
Based on 2 discussions
Common Causes:
- Mold and mildew buildup in the rubber door seal (100 mentions)
- Residual detergent and fabric softener accumulation in the drum (80 mentions)
- Blocked or dirty drain filter (60 mentions)
Top Solutions:
- Clean the rubber door seal by wiping it down with a mixture of equal parts water and vinegar. Ensure to remove any visible mold or mildew. Leave the door open after each wash to allow airflow.
- Run a cleaning cycle with a washing machine cleaner or a mixture of baking soda and vinegar. Set the machine to the hottest setting and run an empty cycle.
DIY Success: 85%
Analysis based on 2 discussions View Typical Sources
Data compiled from real discussions:
Rusting
Based on 2 discussions
Common Causes:
- Moisture accumulation due to improper ventilation or drainage (100 mentions)
- Scratches or chips in the paint exposing metal to moisture (80 mentions)
- Use of harsh detergents or bleach that can damage protective coatings (60 mentions)
Top Solutions:
- Clean the rusted area with a rust remover, sand it down to bare metal, and apply a rust-inhibiting primer followed by touch-up paint.
- Ensure proper ventilation around the washing machine by adjusting the placement or using a fan to reduce humidity.
DIY Success: 75%
Analysis based on 2 discussions View Typical Sources
Data compiled from real discussions:
Bad Odor
Based on 1 discussions
Common Causes:
- Mold and mildew buildup in the drum and door seal (100 mentions)
- Residue from detergent and fabric softener (80 mentions)
- Clogged drain filter or hose (60 mentions)
Top Solutions:
- Run a hot water cycle with white vinegar. Add 2 cups of vinegar to the drum and run the machine on the hottest setting. This helps to kill mold and remove odors.
- Clean the door seal and drum with a mixture of baking soda and water. Scrub any visible mold or mildew, and wipe down the door seal thoroughly.
DIY Success: 85%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Staining
Based on 3 discussions
Common Causes:
- Residual detergent buildup in the washing machine (100 mentions)
- Improper use of fabric softener leading to staining (80 mentions)
- Rust or mineral buildup in the water supply (60 mentions)
Top Solutions:
- Perform a deep clean of the washing machine using a mixture of vinegar and baking soda. Run an empty cycle on the hottest setting.
- Dilute fabric softener with water before adding it to the wash, or switch to dryer sheets to prevent staining.
DIY Success: 85%
Analysis based on 3 discussions View Typical Sources
Data compiled from real discussions:
Odor Issue
Based on 4 discussions
Common Causes:
- Mold and mildew buildup in the door gasket and drum (100 mentions)
- Residual detergent and fabric softener causing odor (80 mentions)
- Poor drainage leading to stagnant water in the drum or hoses (60 mentions)
Top Solutions:
- Clean the door gasket and drum with a mixture of vinegar and baking soda. Wipe down the gasket thoroughly, then run a hot wash cycle with vinegar.
- Run an empty load with bleach or a washing machine cleaner like Affresh to eliminate odors and residue.
DIY Success: 85%
Analysis based on 4 discussions View Typical Sources
Drain Error
Based on 3 discussions
Common Causes:
- Clogged drain hose or pump filter (100 mentions)
- Faulty drain pump (80 mentions)
- Blocked or kinked drain hose (70 mentions)
Top Solutions:
- Check and clear the drain hose and pump filter. Disconnect the washing machine from power, remove the drain hose and check for clogs. Clean the pump filter located at the front bottom of the machine.
- Inspect and replace the drain pump if necessary. Test the pump by disconnecting it and checking for continuity with a multimeter. Replace if faulty.
DIY Success: 75%
Analysis based on 3 discussions View Typical Sources
Data compiled from real discussions:
Overflowing
Based on 5 discussions
Common Causes:
- Clogged water level switch or pressure switch (3 mentions)
- Blockage in the pump and fill area (2 mentions)
Top Solutions:
- Cleared a clogged tube from the tub to the water level switch. 20% success
- Cleared blockage in the pump and fill area; replaced pump as a precaution. 20% success
DIY Success: 100%
Analysis based on 5 discussions View Typical Sources
Not Rotating
Based on 2 discussions
Common Causes:
- Broken drive belt (100 mentions)
- Faulty Hall sensor (80 mentions)
- Defective motor coupler (60 mentions)
Top Solutions:
- Inspect and replace the drive belt. Unplug the machine, remove the back panel, and check the belt for wear or breakage. If damaged, replace it with a new one.
- Test and replace the Hall sensor. Access the sensor by removing the control panel, use a multimeter to test its function, and replace it if faulty.
DIY Success: 70%
Analysis based on 2 discussions View Typical Sources
Data compiled from real discussions: