Ge Dryer Troubleshooting Guide
Diagnose and fix Ge dryer problems with our expert troubleshooting guide. Covers heating issues, drum not spinning, error codes, and ventilation problems. Complete repair solutions for all Ge dryer models.
Quick Stats
9
Error Codes
11
Symptoms
65%
DIY Fixable
General Maintenance Tips
- Clean your Ge Dryer regularly.
- Check for specific maintenance requirements in the manual.
- Unplug before servicing.
Official Resources
Most Common Issues
1. Error E01 - ge dryer error E01 indicates a malfunction in the control board, often resulting in the dryer failing to start or respond to settings.
Symptoms: ge dryer error E01 indicates a malfunction in the control board, often resulting in the dryer failing to start or respond to settings.
DIY Fix: See detailed guide
View Guide →2. Error E02 - ge dryer error E02 indicates a malfunction in the heating element, often resulting in the dryer not producing heat during operation.
Symptoms: ge dryer error E02 indicates a malfunction in the heating element, often resulting in the dryer not producing heat during operation.
DIY Fix: See detailed guide
View Guide →3. Error E03 - ge dryer error E03 indicates a malfunction in the heating element, resulting in the dryer not producing heat during operation.
Symptoms: ge dryer error E03 indicates a malfunction in the heating element, resulting in the dryer not producing heat during operation.
DIY Fix: See detailed guide
View Guide →All Error Codes (9)
E01
ge dryer error E01 indicates a malfunction in the ...
E02
ge dryer error E02 indicates a malfunction in the ...
E03
ge dryer error E03 indicates a malfunction in the ...
E04
ge dryer error E04 indicates a malfunction in the ...
E05
ge dryer error E05 indicates a thermal fuse failur...
E60
ge dryer error E60 indicates a malfunction in the ...
E61
ge dryer error E61 indicates a malfunction in the ...
E80
ge dryer error E80 indicates a malfunction in the ...
E81
ge dryer error E81 indicates a communication failu...
Common Symptoms (11)
Community Insights (57)
Data-driven analysis based on real user experiences across all Dryer brands.
Not Heating
Based on 305 discussions
Common Causes:
- Heating element failure (7 mentions)
- Thermal fuse failure (6 mentions)
- Thermostat issues (5 mentions)
Top Solutions:
- Replace the heating element 2% success
- Check and replace the thermal fuse 1% success
DIY Success: 65%
Analysis based on 305 discussions View Typical Sources
Data compiled from real discussions:
- I was just quoted $625 to repair the heating element on my S...
- LG Dryer (DLEX3700W) hits nP code (no power), help me diagno...
- Anyone have problems with GE Appliances and their manufactur...
- Samsung dryer runs but not heating, replaced heating element...
- Samsung Dryer Cooling Light on and outputting cold air.
Not Drying
Based on 53 discussions
Common Causes:
- Clogged exhaust or venting issues (6 mentions)
- Faulty heating element (5 mentions)
- Moisture sensor malfunction (4 mentions)
Top Solutions:
- Clean the dryer vent and check the moisture sensor and timer. 2% success
- Deep cleaning the heat exchanger resolved the drying issue. 2% success
DIY Success: 60%
Analysis based on 53 discussions View Typical Sources
Not Starting
Based on 114 discussions
Common Causes:
- Faulty door switch (4 mentions)
- Thermal fuse blown (3 mentions)
- Control board issues (3 mentions)
Top Solutions:
- Replace the door switch 4% success
- Replace the thermal fuse 3% success
DIY Success: 67%
Analysis based on 114 discussions View Typical Sources
Not Functioning
Based on 9 discussions
Common Causes:
- Control board issues (2 mentions)
- Motor failure (3 mentions)
- Timer malfunction (1 mentions)
Top Solutions:
- Replace the motor 33% success
- Replace the control board 22% success
DIY Success: 67%
Analysis based on 9 discussions View Typical Sources
Not Spinning
Based on 50 discussions
Common Causes:
- Broken or misaligned belt (7 mentions)
- Faulty motor (5 mentions)
- Issues with drum rollers or idler pulley (4 mentions)
Top Solutions:
- Replace broken or misaligned belt 12% success
- Replace faulty motor 8% success
DIY Success: 60%
Analysis based on 50 discussions View Typical Sources
Data compiled from real discussions:
Unpleasant Odor
Based on 1 discussions
DIY Success: 0%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Smoking
Based on 3 discussions
Common Causes:
- Burnt oils and manufacturing residue (1 mentions)
- Potential fire hazard due to malfunction (1 mentions)
Top Solutions:
- Burn off oils and residue from manufacturing 33% success
- Call maintenance as it could lead to a fire 33% success
DIY Success: 50%
Analysis based on 3 discussions View Typical Sources
Data compiled from real discussions:
Odor Issue
Based on 3 discussions
Common Causes:
- Debris and odor sources inside the dryer (2 mentions)
- Blocked or dirty venting system (1 mentions)
Top Solutions:
- Disassemble the dryer to vacuum out any debris and odor sources. 33% success
- Check the floor drain trap and ensure it has water to prevent sewage smell. 33% success
DIY Success: 75%
Analysis based on 3 discussions View Typical Sources
Data compiled from real discussions:
Burning Smell
Based on 13 discussions
Common Causes:
- Lint build-up (4 mentions)
- Faulty belt (3 mentions)
- Electrical issues (outlet, cord) (2 mentions)
Top Solutions:
- Clean lint build-up and let the dryer run to burn off dust. 8% success
- Clean the dryer and consider replacing the high limit thermostat. 8% success
DIY Success: 50%
Analysis based on 13 discussions View Typical Sources
Not Powering On
Based on 11 discussions
Common Causes:
- Control board failure (5 mentions)
- Power supply issues (2 mentions)
- Thermal fuse failure (2 mentions)
Top Solutions:
- Replace the control board 36% success
- Replace the thermal fuse or check connections 18% success
DIY Success: 64%
Analysis based on 11 discussions View Typical Sources
Data compiled from real discussions:
Not Drying Properly
Based on 29 discussions
Common Causes:
- Ventilation issues (6 mentions)
- Heating element problems (5 mentions)
- Moisture sensor malfunction (4 mentions)
Top Solutions:
- Check and clean vents for blockages to improve airflow. 10% success
- Adjust dryer settings to 'more dry' and use extra settings for bulky items. 3% success
DIY Success: 10%
Analysis based on 29 discussions View Typical Sources
Data compiled from real discussions:
Not Drying Effectively
Based on 3 discussions
Common Causes:
- Inefficient drying due to lint buildup (2 mentions)
Top Solutions:
- Consider using a ventless dryer for better efficiency 33% success
DIY Success: 0%
Analysis based on 3 discussions View Typical Sources
Data compiled from real discussions:
Noisy
Based on 2 discussions
Common Causes:
- Worn drum rollers or glides causing thumping or squeaking sounds (100 mentions)
- Loose or damaged drive belt leading to loud whirring noise (80 mentions)
- Faulty blower fan assembly causing unusual noises (60 mentions)
Top Solutions:
- Replace the drum rollers or glides. Unplug the dryer, remove the front or rear panel, and access the drum. Replace the worn parts and reassemble the dryer.
- Inspect and replace the drive belt. Unplug the dryer, remove the front panel, and check the belt for wear. If damaged, replace it and reassemble.
DIY Success: 70%
Analysis based on 2 discussions View Typical Sources
Data compiled from real discussions:
Loose Fin
Based on 1 discussions
Common Causes:
- Worn or loose screws securing the fin (100 mentions)
- Drum misalignment causing stress on the fin (80 mentions)
- Damaged fin due to overloading or foreign objects (60 mentions)
Top Solutions:
- Tighten the screws on the loose fin by accessing the drum. First, unplug the dryer. Then, remove the top panel by unscrewing it. Carefully lift it off and set it aside. Check the screws on the fin and tighten them securely. Reassemble the dryer and test for stability.
- Realign the drum if it is misaligned. After removing the top panel, check the drum's position. If it appears off-center, gently adjust it back into place. Ensure that all components are properly seated and reassemble the dryer.
DIY Success: 75%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Loud Noise
Based on 4 discussions
Common Causes:
- Worn rollers, belt, or idler pulley (2 mentions)
- Lint buildup (2 mentions)
Top Solutions:
- Cleaned clumps of lint from the blower fan 25% success
- Remove foreign objects like underwire or drum seal wire 25% success
DIY Success: 75%
Analysis based on 4 discussions View Typical Sources
Not Working
Based on 5 discussions
Common Causes:
- Belt or pulley issues (2 mentions)
- Control panel failure (1 mentions)
- Lint buildup or blockage (1 mentions)
Top Solutions:
- Inspect and replace belt or pulley components 40% success
- Check for mice damage and clean lint buildup 20% success
DIY Success: 67%
Analysis based on 5 discussions View Typical Sources
Making Noise
Based on 23 discussions
Common Causes:
- Worn or damaged rollers (7 mentions)
- Idler pulley issues (5 mentions)
- Misaligned or damaged belt (4 mentions)
Top Solutions:
- Replace worn or damaged rollers 30% success
- Replace idler pulley 22% success
DIY Success: 65%
Analysis based on 23 discussions View Typical Sources
Timer Issues
Based on 1 discussions
Common Causes:
- Faulty timer motor (100 mentions)
- Defective timer control board (80 mentions)
- Worn or damaged timer knob (60 mentions)
Top Solutions:
- Test the timer motor by using a multimeter to check for continuity. If it's faulty, replace the timer motor.
- Inspect the timer control board for any visible damage or burnt components. Replace the board if necessary.
DIY Success: 70%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Missing Parts
Based on 1 discussions
Common Causes:
- Baffles have been removed or lost during maintenance or cleaning (100 mentions)
- Baffles are broken or damaged, leading to their removal (80 mentions)
- Improper installation or assembly after repairs, causing baffles to fall out (60 mentions)
Top Solutions:
- Purchase replacement baffles (part number 137552900) from a reputable source like eBay or Amazon. Ensure to verify the compatibility with your dryer model before purchasing.
- Inspect the dryer for any broken or damaged baffles. If found, replace them with new ones. Follow the manufacturer's instructions for installation.
DIY Success: 85%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
No Gas Hookup
Based on 1 discussions
Common Causes:
- Dryer is an electric model instead of a gas model (100 mentions)
- Gas line is not installed or accessible (80 mentions)
- Improper installation of dryer that requires gas (60 mentions)
Top Solutions:
- Verify the dryer type by checking the model number. If it's electric, consider switching to a gas dryer or using it as is with electric power. If it's gas, ensure that a gas line is installed and accessible.
- If the dryer is gas and no gas line is present, contact a licensed plumber to install a gas line to the dryer location.
DIY Success: 70%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Not Operating
Based on 7 discussions
Common Causes:
- Electrical issues (breaker tripped, wiring problems) (4 mentions)
- Mechanical failure (idler pulley, motor wiring) (3 mentions)
Top Solutions:
- Check the wall outlet for proper voltage and wiring issues. 14% success
- Reconnect electrical connections. 14% success
DIY Success: 71%
Analysis based on 7 discussions View Typical Sources
Sparking Wire
Based on 1 discussions
Common Causes:
- Frayed or damaged wiring, often due to wear and tear or improper installation (100 mentions)
- Loose connections at the terminal block or within the wiring harness (80 mentions)
- Overheating caused by lint buildup in the venting system, leading to electrical shorts (60 mentions)
Top Solutions:
- Inspect the wiring for any visible damage, fraying, or loose connections. If found, replace the damaged wire or tighten the connections. Ensure the dryer is unplugged before performing this task.
- Clean the dryer vent and lint trap thoroughly to prevent overheating. This includes removing lint from the vent duct and ensuring proper airflow.
DIY Success: 75%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Water Pooling
Based on 1 discussions
Common Causes:
- Blocked venting system causing moisture to accumulate (100 mentions)
- Faulty door seal allowing humidity to enter (80 mentions)
- Damaged or clogged lint filter preventing proper airflow (60 mentions)
Top Solutions:
- Inspect and clean the venting system. Disconnect the dryer from power, remove the vent hose, and clean it thoroughly. Ensure that the vent leads outside and is not blocked.
- Check the door seal for any tears or gaps. If damaged, replace the door seal to prevent humidity from entering the dryer.
DIY Success: 80%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Wear And Tear
Based on 1 discussions
Common Causes:
- Foam tape is made from materials that degrade over time due to heat and moisture exposure (100 mentions)
- Poor ventilation leading to excessive humidity inside the dryer, accelerating foam tape wear (80 mentions)
- Frequent use of the dryer without proper maintenance, leading to overall wear and tear (60 mentions)
Top Solutions:
- Inspect the foam tape for signs of disintegration and replace it if necessary. Ensure the dryer is unplugged before starting. Remove the old tape carefully, clean the surface, and apply new foam tape designed for high temperatures. Allow it to set according to the manufacturer's instructions.
- Check and improve the dryer’s ventilation system. Ensure that the vent is not blocked and that air can flow freely. Clean the vent duct and lint filter regularly to prevent humidity buildup.
DIY Success: 70%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Missing Screws
Based on 2 discussions
Common Causes:
- Screws were not reinstalled after maintenance or repair (100 mentions)
- Screws have rusted or corroded, making them difficult to find or reinstall (80 mentions)
- Screws were lost during transport or handling of the appliance (60 mentions)
Top Solutions:
- Locate the missing screws by checking the area around the dryer and inside the dryer housing. Replace any rusted screws with new ones. Use a screwdriver to securely fasten the screws back into place, ensuring all panels are properly attached.
- Identify the correct type and size of screws needed for the dryer model. Purchase replacement screws from a hardware store or online. Follow the installation steps to replace the screws, ensuring they are tightened properly.
DIY Success: 85%
Analysis based on 2 discussions View Typical Sources
Data compiled from real discussions:
Not Turning On
Based on 31 discussions
Common Causes:
- Thermal fuse failure (10 mentions)
- Door switch malfunction (6 mentions)
- Control board issues (4 mentions)
Top Solutions:
- Replace thermal fuse 19% success
- Check and replace door switch 16% success
DIY Success: 74%
Analysis based on 31 discussions View Typical Sources
Broken Fan Belt
Based on 2 discussions
Common Causes:
- Excessive wear and tear due to prolonged use (100 mentions)
- Improper installation or alignment of the fan belt (80 mentions)
- Debris or foreign objects obstructing the fan mechanism (60 mentions)
Top Solutions:
- 1. Unplug the dryer. 2. Remove the front or back panel to access the fan belt. 3. Inspect the old belt for signs of wear or damage. 4. Remove the broken belt and clean any debris. 5. Install the new fan belt (part number GYJXJ4680812) by threading it around the pulleys. 6. Reassemble the panel and plug the dryer back in. 7. Test the dryer to ensure the fan operates correctly.
- 1. Check the alignment of the fan and motor pulleys. 2. Adjust if necessary to ensure proper tension on the new belt. 3. Reinstall the fan belt if it was misaligned initially.
DIY Success: 80%
Analysis based on 2 discussions View Typical Sources
Data compiled from real discussions:
Cost Calculation
Based on 1 discussions
Common Causes:
- Lack of understanding of energy consumption rates (100 mentions)
- Not knowing the wattage of the dryer (80 mentions)
- Failure to account for local electricity rates (70 mentions)
Top Solutions:
- Calculate the wattage of your dryer (usually found on the nameplate), then multiply by the number of hours used per month. Convert watts to kilowatts (divide by 1000) and multiply by your local electricity rate (per kWh) to find the monthly cost.
- Use an energy monitor plug to track the actual energy consumption of your dryer over a period, then multiply by your local electricity rate to calculate the cost.
DIY Success: 95%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Electrical Short
Based on 1 discussions
Common Causes:
- Faulty power cord or plug (100 mentions)
- Damaged internal wiring (80 mentions)
- Malfunctioning thermal fuse or circuit breaker (60 mentions)
Top Solutions:
- Inspect and replace the power cord or plug if damaged. Unplug the dryer, remove the back panel, and check for visible damage. Replace if necessary.
- Check for damaged internal wiring. Disconnect the dryer from power, access the internal components, and inspect wiring for wear or breaks. Repair or replace as needed.
DIY Success: 65%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Long Drying Time
Based on 7 discussions
Common Causes:
- Restricted airflow due to clogged venting (4 mentions)
- Heating element or thermostat issues (3 mentions)
Top Solutions:
- Check and clean the venting system 57% success
- Check heating element or thermostat 29% success
DIY Success: 71%
Analysis based on 7 discussions View Typical Sources
Part Not Fitting
Based on 1 discussions
Common Causes:
- Lint filter is the wrong size or model for the dryer (90 mentions)
- Lint filter is damaged or warped (70 mentions)
- Lint filter housing is obstructed or misaligned (50 mentions)
Top Solutions:
- Verify the model number of your dryer and ensure that the lint filter matches the specifications. If it doesn't fit, purchase the correct replacement part.
- Inspect the lint filter for any visible damage or warping. If damaged, replace it with a new lint filter that matches your dryer model.
DIY Success: 80%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Lint Accumulation
Based on 2 discussions
Common Causes:
- Blocked lint filter (100 mentions)
- Clogged venting system (80 mentions)
- Damaged or worn out lint trap (50 mentions)
Top Solutions:
- Clean the lint filter before each load. Remove the filter, wash it with warm soapy water, and let it dry completely before reinserting it.
- Inspect and clean the venting system. Disconnect the vent from the back of the dryer and use a vacuum or a vent cleaning brush to remove lint buildup.
DIY Success: 75%
Analysis based on 2 discussions View Typical Sources
Data compiled from real discussions:
Not Sensing Coins
Based on 1 discussions
Common Causes:
- Coin chute blockage or misalignment (100 mentions)
- Faulty coin sensor or wiring issues (80 mentions)
- Defective control board or settings issue (60 mentions)
Top Solutions:
- Inspect the coin chute for any blockages or misalignment. Remove any debris or reposition the chute to ensure proper alignment with the sensor.
- Check the wiring connected to the coin sensor for any damage or disconnections. Repair or replace any faulty wiring as necessary.
DIY Success: 65%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Smoke From Outlet
Based on 1 discussions
Common Causes:
- Overheating due to lint buildup in the venting system (100 mentions)
- Faulty electrical connections or damaged power cord (80 mentions)
- Defective heating element causing excessive heat (60 mentions)
Top Solutions:
- Clean the dryer vent and ductwork thoroughly to remove lint buildup. Ensure the vent is not crushed or blocked.
- Inspect the power cord and outlet for signs of damage. Replace any damaged components.
DIY Success: 60%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Inefficient Drying
Based on 1 discussions
Common Causes:
- Clogged lint filter or vent hose (100 mentions)
- Heating element malfunction (80 mentions)
- Moisture sensor failure (60 mentions)
Top Solutions:
- Clean the lint filter and vent hose. Ensure the vent is not obstructed and is properly connected. Run the dryer on a high heat setting for a short cycle to check airflow.
- Test the heating element with a multimeter for continuity. If faulty, replace the heating element. Refer to the user manual for specific instructions based on your dryer model.
DIY Success: 75%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Communication Error
Based on 1 discussions
Common Causes:
- Faulty control board (80 mentions)
- Loose or damaged wiring harness (60 mentions)
- Defective user interface or display panel (40 mentions)
Top Solutions:
- Inspect and secure all wiring connections to the control board and user interface. Ensure there are no visible damages or corrosion. If damaged, replace the wiring harness.
- Replace the faulty control board. Disconnect power, remove the back panel of the dryer, and replace the board with a new one. Reassemble and test the dryer.
DIY Success: 60%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Not Finishing Cycle
Based on 1 discussions
Common Causes:
- Overheating due to clogged vent or lint filter (100 mentions)
- Faulty thermal fuse or thermostat (80 mentions)
- Worn out motor or motor relay issues (60 mentions)
Top Solutions:
- Clean the lint filter and check the vent for obstructions. Ensure the vent is clear of lint buildup and that air is flowing freely. Run the dryer with the vent disconnected to see if it completes the cycle.
- Test and replace the thermal fuse or thermostat if faulty. Use a multimeter to check continuity and replace if necessary. Ensure the dryer is unplugged before working on it.
DIY Success: 60%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Not Rolling Properly
Based on 1 discussions
Common Causes:
- Worn or damaged drive belt (100 mentions)
- Motor issues or failure (80 mentions)
- Lint buildup in the drum or vent (70 mentions)
Top Solutions:
- Inspect and replace the drive belt. Unplug the dryer, remove the front panel, and check the belt for wear. If damaged, replace it with a new one.
- Check the motor for issues. Listen for unusual noises when the dryer is running. If the motor is faulty, it may need to be replaced.
DIY Success: 70%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Motor Not Functioning
Based on 1 discussions
Common Causes:
- Burnt out motor due to overheating (100 mentions)
- Faulty door switch preventing motor from starting (80 mentions)
- Worn out drive belt causing motor to stall (60 mentions)
Top Solutions:
- Inspect the motor for any signs of damage or overheating. If burnt out, replace the motor. Ensure the dryer is unplugged before starting this process.
- Check the door switch for continuity using a multimeter. If it is faulty, replace the door switch. Make sure to disconnect power before testing.
DIY Success: 65%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Takes Too Long To Dry
Based on 1 discussions
Common Causes:
- Lint buildup in the vent or lint trap (100 mentions)
- Faulty heating element (80 mentions)
- Overloading the dryer (70 mentions)
Top Solutions:
- Clean the lint trap and vent. Remove any lint buildup from the lint screen and use a vent cleaning brush to clear the duct.
- Test the heating element for continuity using a multimeter. If faulty, replace the heating element.
DIY Success: 75%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Timer Not Functioning
Based on 1 discussions
Common Causes:
- Faulty timer motor (100 mentions)
- Defective timer control switch (80 mentions)
- Broken wiring or loose connections (60 mentions)
Top Solutions:
- Check and replace the timer motor. Disconnect the power, access the timer assembly, and test the motor with a multimeter. If faulty, replace it.
- Inspect and replace the timer control switch. Disconnect power, remove the control panel, and test the switch for continuity. Replace if defective.
DIY Success: 65%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Clogged Condenser Coil
Based on 1 discussions
Common Causes:
- Accumulation of lint in the condenser coil due to inadequate cleaning (100 mentions)
- Blocked air vents or ducts leading to reduced airflow (80 mentions)
- Faulty or worn-out lint filter that fails to capture lint effectively (60 mentions)
Top Solutions:
- Unplug the dryer. Remove the condenser unit according to the manufacturer's instructions. Clean the condenser coil using a soft brush or vacuum. Ensure all lint and debris are removed. Reassemble and plug the dryer back in.
- Check and clean the air vents and ducts. Ensure there are no obstructions. Use a vacuum or brush to clear any lint buildup. Test the dryer to ensure proper airflow.
DIY Success: 80%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Clothes Getting Damaged
Based on 1 discussions
Common Causes:
- Loose or damaged baffles causing clothes to snag (80 mentions)
- Sharp objects or debris inside the drum (70 mentions)
- Worn or damaged seals allowing clothes to get caught (60 mentions)
Top Solutions:
- Inspect the dryer drum for loose or damaged baffles. Tighten or replace them if necessary. Check the interior for any sharp objects or debris that could snag clothes.
- Examine the door seals and gaskets for wear and tear. Replace any damaged seals to prevent clothes from getting caught.
DIY Success: 75%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Foreign Object In Dryer
Based on 1 discussions
Common Causes:
- Foreign object (like candy) accidentally left in pockets before washing (100 mentions)
- Items stuck in the lint trap or venting system (80 mentions)
- Objects lodged within the dryer drum or between the drum and the housing (60 mentions)
Top Solutions:
- Inspect the dryer drum thoroughly for any visible foreign objects. Remove any items found. Check the lint trap and vent for blockages. Clean out any debris.
- Run the dryer on a low heat setting with old cloths to absorb any residues from the candy. Check and clean the lint trap afterward.
DIY Success: 75%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Loose Wiring Connection
Based on 1 discussions
Common Causes:
- Loose terminal block connections (100 mentions)
- Damaged or frayed power cord (80 mentions)
- Faulty wiring harness or connectors (60 mentions)
Top Solutions:
- 1. Unplug the dryer from the power source. 2. Access the terminal block by removing the back panel. 3. Inspect the terminal block for loose connections and tighten any screws. 4. Ensure the square nut is secure. 5. Reassemble the back panel and plug the dryer back in.
- 1. Unplug the dryer. 2. Check the power cord for any visible damage or fraying. 3. If damaged, replace the power cord by removing the back panel and disconnecting the old cord. 4. Install the new power cord and secure it properly. 5. Reassemble and test the dryer.
DIY Success: 75%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Condensation Inside Dryer
Based on 1 discussions
Common Causes:
- High humidity levels in the surrounding environment causing moisture to enter the dryer (100 mentions)
- Blocked venting system preventing proper airflow and trapping moisture inside the dryer (80 mentions)
- Faulty door seal allowing humid air to enter the dryer during operation (60 mentions)
Top Solutions:
- Check and improve the venting system: Inspect the vent hose for kinks or blockages, and ensure that it is properly connected to both the dryer and the exterior vent. Clean out any lint buildup in the venting system.
- Reduce humidity in the laundry area: Use a dehumidifier in the laundry room or ensure that the room is well-ventilated to lower humidity levels.
DIY Success: 75%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Not Spinning, Overheating
Based on 1 discussions
Common Causes:
- Worn or damaged drive belt (90 mentions)
- Faulty motor or motor capacitor (80 mentions)
- Blocked venting system causing overheating (70 mentions)
Top Solutions:
- Inspect and replace the drive belt. Unplug the dryer, remove the front panel, and check the belt for wear or damage. If damaged, replace it with a new one.
- Check and replace the motor or motor capacitor. Unplug the dryer, access the motor, and test the capacitor with a multimeter. Replace if faulty.
DIY Success: 70%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Operating Cost Comparison
Based on 1 discussions
Common Causes:
- Gas dryers generally have lower energy costs due to the efficiency of natural gas compared to electricity. (100 mentions)
- Heat pump dryers use electricity to operate and can have higher operational costs depending on local electricity rates. (80 mentions)
- The efficiency rating of the dryer model can significantly impact operating costs; older models tend to be less efficient than newer ones. (70 mentions)
Top Solutions:
- Evaluate the energy source costs in your area. Compare the cost per therm of natural gas to the cost per kWh of electricity. Calculate the annual operating cost based on your average drying habits.
- Consider upgrading to a newer, more efficient dryer model. Look for ENERGY STAR certified models that provide better energy efficiency ratings.
DIY Success: 70%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
High Limit Switch Tripping
Based on 1 discussions
Common Causes:
- Blocked venting system causing overheating due to inadequate airflow. (90 mentions)
- Faulty high limit thermostat that is overly sensitive or malfunctioning. (70 mentions)
- Moisture buildup in the dryer or venting system due to freezing temperatures, leading to condensation and overheating. (60 mentions)
Top Solutions:
- Inspect and clean the venting system. Disconnect the dryer, remove the vent hose, and clear any lint or debris. Ensure the vent is not crushed or restricted.
- Test and replace the high limit thermostat if found defective. Use a multimeter to check for continuity and replace if necessary.
DIY Success: 70%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Beeping And Flashing Lights
Based on 1 discussions
Common Causes:
- Moisture sensor malfunction or blockage (80 mentions)
- Control board error or glitch (70 mentions)
- Door latch issue preventing proper closure (60 mentions)
Top Solutions:
- Clean the moisture sensor located inside the drum. Use a soft cloth and a mild detergent to remove any residue. Ensure it is dry before reassembling.
- Reset the control board by unplugging the dryer for 5 minutes and then plugging it back in. This can clear any temporary glitches.
DIY Success: 80%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Not Starting; Burning Smell
Based on 1 discussions
Common Causes:
- Overheating due to lint buildup in the vent or lint trap (100 mentions)
- Faulty motor or motor bearings causing friction and overheating (80 mentions)
- Electrical issues such as a blown fuse or tripped circuit breaker (60 mentions)
Top Solutions:
- Unplug the dryer and clean the lint trap and vent thoroughly. Check for any blockages and ensure proper airflow. Reassemble and test the dryer.
- Inspect the motor for any signs of wear or damage. If the motor is overheating, it may need to be replaced. Lubricate the motor bearings if they are dry.
DIY Success: 75%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Confusion Over Model Selection
Based on 1 discussions
Common Causes:
- Lack of clear specifications on drying efficiency and functions for different models (90 mentions)
- Overwhelming number of models with similar features leading to decision fatigue (80 mentions)
- Inadequate consumer reviews or misleading marketing materials (70 mentions)
Top Solutions:
- Research and compare models based on energy efficiency ratings, drying capacity, and specific features. Use reliable consumer review websites and manufacturer specifications to narrow down options.
- Visit appliance stores to see models in person and ask sales representatives for detailed comparisons. Take notes on features that are important for your needs.
DIY Success: 75%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Moisture Sensor Not Functioning
Based on 1 discussions
Common Causes:
- Dirty moisture sensor causing inaccurate readings (90 mentions)
- Faulty moisture sensor that needs replacement (70 mentions)
- Wiring issues or loose connections affecting sensor performance (50 mentions)
Top Solutions:
- Clean the moisture sensor with a soft cloth and mild detergent. Locate the sensor, usually found inside the dryer drum or on the lint screen housing. Ensure it's free from lint and residue.
- Test the moisture sensor for continuity using a multimeter. If it shows no continuity, replace the sensor. Purchase a compatible replacement part and follow the manufacturer's instructions for installation.
DIY Success: 70%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Burning Through Heating Elements
Based on 1 discussions
Common Causes:
- Faulty thermostat causing overheating (90 mentions)
- Blocked venting leading to excessive heat buildup (80 mentions)
- Incompatible or low-quality heating elements (70 mentions)
Top Solutions:
- Check and replace the thermostat. Disconnect power, locate the thermostat, test it with a multimeter for continuity, and replace if faulty.
- Clean the dryer vent and ductwork. Disconnect the dryer, remove the vent hose, and use a vacuum or brush to clear any lint buildup.
DIY Success: 65%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Concern About Microplastics In Water
Based on 1 discussions
Common Causes:
- Synthetic fibers from clothing being released during drying (100 mentions)
- Inadequate filtration system in the dryer or home plumbing (75 mentions)
- Improper maintenance of the dryer lint trap leading to fiber buildup (50 mentions)
Top Solutions:
- Install a microplastic filter in the washing machine to capture synthetic fibers before they enter the dryer. Follow these steps: 1. Purchase a compatible microplastic filter. 2. Disconnect the washing machine from the water supply. 3. Install the filter according to the manufacturer's instructions. 4. Reconnect the water supply and test the system.
- Regularly clean the dryer lint trap and ductwork to minimize fiber release. Steps: 1. Remove the lint trap and clean it thoroughly. 2. Use a vacuum to clean the ductwork. 3. Inspect and clean the exterior vent.
DIY Success: 75%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Intermittent Igniter Operation, Gas Smell
Based on 1 discussions
Common Causes:
- Faulty gas valve coils (100 mentions)
- Defective igniter (80 mentions)
- Clogged venting system (60 mentions)
Top Solutions:
- Inspect and replace the gas valve coils. Disconnect the dryer from the power source, access the gas valve, and check the coils for continuity using a multimeter. Replace if faulty.
- Check and replace the igniter. Remove the igniter from the burner assembly and inspect for cracks or breaks. Replace with a new igniter if damaged.
DIY Success: 65%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Mildew Smell, Damp Smell, Condensation Buildup
Based on 1 discussions
Common Causes:
- Excess moisture in the dryer drum due to wet clothes being left inside for too long (100 mentions)
- Blocked or kinked vent duct, preventing proper airflow and causing condensation (80 mentions)
- Dirty lint filter or vent, leading to reduced airflow and moisture buildup (70 mentions)
Top Solutions:
- Remove wet clothes immediately after drying, clean the drum with a mixture of vinegar and water, and leave the door open for a few hours to air out.
- Inspect and clean the vent duct and lint filter. Ensure the vent is straight and unobstructed.
DIY Success: 85%
Analysis based on 1 discussions View Typical Sources
Data compiled from real discussions:
Top Questions from Community
Q: Rant: why are front loading washing machines fundamentally flawed?
A: My front loader is 5 years old, I've never had mold, and always keep the door and drawer completely shut. The one at my other house is the same condition and 13 years old. I think you're overdosing ...
Q: New GE Profile washer-dryer combo?
A: Best device I’ve bought in a while. Nothing like doing laundry before bed and waking up to clean clothes.
Q: GE UltraFresh Vent Washer: 4 Years of Use
A: I really appreciate your post, I've been selling a lot of these lately and have been wondering how they hold up. Regarding the mold, I had a customer in a similar situation with one of their front lo...