AEG Washing Machine Error C2
⚡ Quick Answer: The AEG Washing Machine C2 error indicates a malfunction in the water drainage system, often caused by a blocked drain pump filter or a kinked drain h... ✅ DIY Fixable
What Does Error C2 Mean?
The AEG Washing Machine C2 error indicates a malfunction in the water drainage system, often caused by a blocked drain pump filter or a kinked drain hose. This error typically results in the machine stopping mid-cycle, accompanied by two beeps or flashes, and water remaining in the drum. To resolve this issue, check the drain pump filter for obstructions and ensure the drain hose is correctly installed and free of blockages.
Common Symptoms:
- Washing machine stops mid-cycle and displays C2
- Two beeps or two LED flashes accompany the error
- Water remains in the drum and does not drain
- Pump/filter struggles or hums without expelling water
Possible Causes
- Blocked or obstructed drain pump filter (high)
- Kinked or incorrectly positioned drain hose (high)
- Faulty or blocked drain pump (medium)
How to Fix Error C2
DIY Fix Check and clean drain pump filter & hose
- Turn off and unplug the washing machine.
- Locate and open the access panel at the base front of the machine.
- Place a shallow tray or towel underneath to catch water.
- Remove and clean the drain pump filter, removing lint, coins or debris.
- Inspect the pump impeller (if visible) and gently rotate to ensure it moves freely.
- Check the drain hose for kinks, twists, or obstructions and straighten or clear as needed.
- Reassemble and run a rinse/drain cycle.
DIY Fix Ensure correct drain hose installation
- Verify drain hose height is between approximately 60–100 cm above base level.
- Ensure the hose is not inserted too far into the standpipe (no more than ~10 cm).
- Check the external plumbing (sink/trap) for blockages by testing drainage manually.
Technician Only Inspect/replace drain pump and motor assembly
- Disconnect power and water, remove machine back or base panel.
- Test pump electrical continuity and impeller motion.
- Remove and examine pump assembly for mechanical failure.
- Replace the pump motor or associated hardware if defective.
Parts needed: drain pump assembly, pump seal or gaskets, possible hose sections
- If water remains after cleaning and checking hoses
- If the pump makes unusual noises or tests faulty
- If you are unsure about disassembling any internal components
Next step
Choose the next step for C2
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Drain Pump
Pumps waste water out of the appliance during the drain cycle.
- Typical part-only price
- $35 - $80
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Model-compatible Washing Machine parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Washing Machine Cleaner Tablets
Routine tub-cleaning supplies for residue and odor control. They do not repair a mechanical, drainage, or electronic fault.
Braided Washer Inlet Hoses
A maintenance replacement option for visibly worn external fill hoses. Verify thread size, length, and hot/cold connection requirements.
Washer Drain Hose Holder
Helps secure an external drain hose at the standpipe. It does not correct an internal pump or control fault.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Technical Specifications
| note | The previous model-independent part specification was removed. Verify the full model number and diagnosis in the manufacturer's official parts catalog before ordering. |
|---|---|
| part_number | None |
Common Questions
What does C2 error mean on AEG Washing Machine?
C2 indicates a water drainage fault, causing the machine to stop mid-cycle and not drain water.
Can I fix AEG Washing Machine C2 error myself?
Yes, you can clean the drain pump filter and check for hose issues.
How much does it cost to fix C2 error?
Estimated repair costs range from $80 to $250, depending on parts and labor.
When should I call a technician for C2?
Call a technician if water remains after cleaning or if the pump makes unusual noises.
Sources & References
Data last verified: 2026-07-31
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!