Maytag Oven Error F10
⚡ Quick Answer: The Maytag oven error code F10 indicates a malfunction related to the temperature sensor, which can cause erratic temperature readings or lead to the ... ✅ DIY Fixable
What Does Error F10 Mean?
The Maytag oven error code F10 indicates a malfunction related to the temperature sensor, which can cause erratic temperature readings or lead to the oven not heating properly. This error typically arises from a faulty temperature sensor, damaged wiring between the sensor and control board, or issues with the electronic control board itself. Symptoms include the display showing F10 and the oven either not reaching the desired temperature or shutting down during operation.
Common Symptoms:
- Oven display shows F10 and stops heating or shuts down
- Oven may not reach correct temperature or thinks internal temperature is outside normal range
- Error appears during heat or immediately on power‑up
Possible Causes
- Faulty oven temperature sensor (RTD/probe) (medium)
- Damaged or loose wiring between temperature sensor and control board (medium)
- Electronic control board malfunction reading sensor data (medium)
How to Fix Error F10
DIY Fix Basic F10 Error Reset and Safety Check
- Turn off/disconnect power to the oven (unplug or via circuit breaker).
- Wait 5–10 minutes to allow internal electronics to fully reset.
- Restore power and attempt to set a bake temperature to see if error clears.
- Ensure oven door is fully closed and vents are unobstructed.
Technician Only Temperature Sensor and Wiring Diagnosis
- Disconnect oven from power at breaker.
- Locate oven temperature sensor (inside oven cavity back wall/probe).
- Remove and test sensor resistance with a multimeter at room temperature.
- Inspect sensor wiring and connectors for damage, corrosion, or loose connections; repair or replace as needed.
- Reconnect and test oven; if F10 persists, proceed to control board evaluation.
Parts needed: Oven temperature sensor (RTD/probe), Wiring harness/connectors
Technician Only Electronic Control Board Evaluation/Replacement
- After confirming sensor and wiring integrity, inspect electronic control board for damage or failed components.
- Test sensor signal input to control board if tools/resources available.
- Replace control board if confirmed defective and specific to Maytag model.
- Verify correct board programming/configuration for the oven model after replacement.
Parts needed: Electronic Oven Control (EOC) board
- If error persists after basic reset and visual inspection.
- If sensor tests within expected resistance but error remains.
- If control board appears damaged or if you are uncomfortable performing live electrical diagnostics.
Next step
Choose the next step for F10
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Temperature Sensor
Monitors the internal temperature to ensure correct operation and prevent overheating.
- Typical part-only price
- $15 - $35
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Wiring Harness
Connects controls, sensors, motors, and other electrical components inside the appliance.
Model-compatible Oven parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Non-Scratch Cooktop Cleaner
A routine surface-care product. Confirm that it is approved for the specific glass, ceramic, enamel, or stainless finish.
Oven Thermometer
A diagnostic aid for comparing cavity temperature during a controlled check. It does not prove which internal component has failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Technical Specifications
| wattage | N/A |
|---|---|
| component | Temperature Sensor |
| resistance | 1000-1200 ohms |
| part_number | W10705551 |
| voltage_rating | 120V AC |
Common Questions
What does F10 error mean on Maytag oven?
F10 error on a Maytag oven signifies a malfunction in the temperature sensor, affecting heating and temperature readings.
Can I fix Maytag oven F10 error myself?
Yes, you can perform a basic reset by turning off the power for 5-10 minutes and checking for any loose wiring.
How much does it cost to fix F10 error?
Repair costs for F10 error range from $30 to $150 for parts, excluding labor.
When should I call a technician for F10?
Call a technician if the error persists after a reset, if the sensor tests good, or if you are unsure about performing electrical diagnostics.
Sources & References
Data last verified: 2026-07-25
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!