Maytag Oven: not heating
What is this symptom?
Experiencing issues with your Maytag oven not heating? This common problem can occur with both gas and electric models, preventing your oven from reaching the desired temperature when baking or roasting. Understanding the potential causes can help you troubleshoot effectively.
Important Tips for Maytag Models
- Maytag troubleshooting highlights weak or dirty ignitors, temperature sensor issues, and calibration errors as common causes for ovens not heating.
Possible Causes
Faulty ignition system (gas ovens)
How to Identify: Igniter does not glow or glows weakly and gas does not ignite; oven remains cold without flame.
Part: Igniter/Burner ignitor
Defective heating element (electric ovens)
How to Identify: Electric element fails to glow red, shows visible damage (cracks/blisters, and has no continuity on multimeter.
Part: Bake heating element
Control board/electronic control failure
How to Identify: Error codes displayed; elements and ignitor not receiving voltage despite power presence; visual burn marks on board.
Part: Oven control board/electronic control
DIY Solutions
Inspect and test the heating element (electric)
- Ensure oven is powered off and cool.
- Remove oven racks and access the heating element.
- Visually inspect for damage and use a multimeter to test continuity.
- Replace the element if no continuity and reassemble.
Check and clean gas ignitor (gas ovens)
- Turn off oven and gas supply.
- Remove access panel and locate the ignitor.
- Gently clean debris and inspect for damage.
- Test by powering oven and observing if it glows brightly; replace if weak or non-functional.
Test temperature sensor/thermostat
- Turn off oven and power.
- Locate the temperature sensor inside the oven cavity.
- Disconnect and test resistance with a multimeter.
- Replace sensor if resistance outside expected range.
Next step
Choose the next step for not heating
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Heating Element
Heats the water or air inside the appliance to the required temperature.
- Typical part-only price
- $40 - $95
- DIY difficulty
- Medium
- Estimated time
- 30-45 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Main Control Board
The central brain of the appliance that controls all components, cycles, and timings.
Model-compatible Oven parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Non-Scratch Cooktop Cleaner
A routine surface-care product. Confirm that it is approved for the specific glass, ceramic, enamel, or stainless finish.
Oven Thermometer
A diagnostic aid for comparing cavity temperature during a controlled check. It does not prove which internal component has failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Professional Repairs
Replace control board/electronic control
Gas valve repair or replacement (gas ovens)
When to Call a Professional
Preventive Maintenance
-
Regularly inspect heating elements and sensors: Unexpected heating failures
Frequency: biannually -
Clean interior and keep vents clear: Heat blockages and sensor misreads
Frequency: monthly
Frequently Asked Questions
Why is my Maytag Oven not heating?
How do I fix Maytag Oven not heating myself?
How much does it cost to fix not heating?
When should I call a technician for not heating?
References & Sources
Community Analytical Insights
Guidance from available sources; statistical claims are shown only for samples of at least 10 discussions
Can I Fix This Myself?
Common Issues Reported by Users
- Igniter failure (6 mentions)
- Control board malfunction (5 mentions)
- Heating element failure (5 mentions)
- Relay board issues (3 mentions)
- Temperature sensor malfunction (3 mentions)
User Suggested Solutions
-
Replace the igniter
-
Replace the control board
-
Replace the heating element
-
Replace the relay board
-
Replace the temperature sensor
Analysis based on 26 community discussions
View
Sources
Data compiled from real discussions on r/appliancerepair and r/Appliances:
- Help with replacing igniter on Maytag gas oven
- Oven not heating after replacing heating element
- Maytag Oven Bake Flame Light, Clicks, Then Turns Off
- Maytag oven doesn't stay lit
- Advice on what could be wrong with the lower heating element...
- Maytag Electric oven - feature not available message
- Maytag oven not heating properly
- Maytag oven diagnosis
- MAYTAG - What if My Baking Element Replacement Doesn't Match...
- Maytag oven won't ignite!
- Maytag gas oven woes
- Maytag Oven Broiler not working
- Maytag Oven MER8700DS1 not heating
- Oven Not Working - Maytag MER8600DS
- Maytag Baking Element Broken in 2 Places
- 30" Maytag slide in kitchen oven model: YMES8800FZ1
- Maytag Oven - Repair or Replace?
- Maytag oven bottom element struggle bus
- Oven preheat going off early.
- Magtag Oven not Heating Correctly
- Maytag gas oven making noises
- Maytag electric over
- Maytag oven not heating properly
- Maytag Oven Repair
- Maytag MER8674AB0 oven inoperative.
- Need help with Maytag electric oven repair!
Community Discussions
The broil element exploded and does not heat after replacement.
Replaced the relays on the control board, which fixed the issue.
struggling preheat in a timely manner
Replaced the broken heating element.
igniter for the bake function stopped working
Replaced the control board, which fixed the oven.
lower heating element won't heat
Replaced the relay board, which fixed the heating issue.
made a loud pop and is toast
Purchased Maytag double oven MET8800FZ, which cooks well compared to the old GE oven.
Source: Reddit r/appliancerepair
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!