Maytag Oven: not working

Possible Causes

Power supply or control lock/demo mode preventing oven from starting

How to Identify: Oven shows no response to controls, display may be blank, Control Lock or Demo Mode enabled, or circuit breaker tripped

Part: Control panel / household circuit breakers / control lock features

Faulty heating element (electric ovens)

How to Identify: Oven doesn’t heat at all or uneven heating even when on; visible breaks, discoloration, or no red glow when heating is selected

Part: Bake/Heating element

Igniter failure (gas ovens)

How to Identify: Gas oven does nothing when turned on and igniter doesn’t glow or generate flame

Part: Oven igniter

DIY Solutions

Reset power and disable control lock/demo mode

Easy 5-10 minutes

1. Locate oven circuit breaker and switch off for 30–60 seconds, then switch back on
2. Check the oven control for a ‘Control Lock’ or similar button and press/hold per manual to disable
3. Check if oven leaves demo mode by entering the correct control combo outlined in manual

⚠️ Safety First: Ensure power is off before touching internal components

Inspect and replace faulty heating element (electric)

Moderate 30–60 minutes

Tools Needed: Screwdriver, Multimeter, Replacement heating element

1. Disconnect power at circuit breaker
2. Remove oven racks and locate heating element
3. Visually inspect for breaks or burns
4. Use multimeter to test continuity; no continuity indicates failure
5. Unplug and remove the old element and install a compatible replacement

⚠️ Safety First: Disconnect power before work

Inspect and replace oven igniter (gas)

Advanced 45–90 minutes

Tools Needed: Multimeter, Screwdriver, Replacement igniter

1. Turn off gas supply and power
2. Remove access panels to reach igniter
3. Test igniter for continuity with a multimeter
4. If failed, disconnect wires and install replacement
5. Restore connections, power, and gas, and test

⚠️ Safety First: Turn off gas supply

Next step

Choose the next step for not working

Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.

Based on diagnostic data

Most relevant component to inspect

Heating Element

Heats the water or air inside the appliance to the required temperature.

Typical part-only price

$40 - $95

DIY difficulty

Medium

Estimated time

30-45 mins

Optional: enter your model number

Apply

Where can I find the model number?

Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.

Find a part that fits my model

Verify the complete model and part number on the retailer's compatibility page before ordering.

Other parts options

Check related components first; use model search as a fallback.

Possible related component

Hot Surface Igniter

Heats until it can ignite gas released by the burner valve in ovens and gas dryers.

$20 - $65 · Medium · 20-45 mins

Check fit & price

Model number required

Model-compatible Oven parts

Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.

Find a part that fits my model

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.

Optional routine care

Maintenance supplies

These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.

Maintenance supply

Non-Scratch Cooktop Cleaner

A routine surface-care product. Confirm that it is approved for the specific glass, ceramic, enamel, or stainless finish.

View maintenance supply

Diagnostic tool

Oven Thermometer

A diagnostic aid for comparing cavity temperature during a controlled check. It does not prove which internal component has failed.

View maintenance supply

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.

Professional Repairs

Replace control board or electronic components

Estimated Cost: $200 - $500+

Gas valve or regulator replacement (gas ovens)

Estimated Cost: $150 - $400+

When to Call a Professional

Persistent power/control issues despite resets

Detection of gas smell or suspected gas leaks

Error codes persist after power cycling

Unresponsive control panel with no display or button response

Preventive Maintenance

• Regularly clean control panel and oven interior: Control glitches and heating element build-up
  Frequency: monthly
• Check door seals for damage: Heat loss and prolonged heating times
  Frequency: annually

Frequently Asked Questions

Why is my Maytag Oven not working?

Common causes include power supply issues, control lock or demo mode, faulty heating elements, or igniter failure.

How do I fix Maytag Oven not working myself?

Try resetting power, disabling the control lock, or inspecting and replacing the heating element or igniter.

How much does it cost to fix not working?

Professional repair costs range from $200 to $500+ for control board replacement and $150 to $400+ for gas valve issues.

When should I call a technician for not working?

Consider calling a technician if DIY fixes are unsuccessful or if the issue involves complex repairs like control board replacement.

References & Sources

• Oven Not Working - Electric - Product Help | Maytag Official
• Maytag Oven Not Working or Lighting: Common Causes Official

Common Issues Reported by Users

• Power supply issue (1 mentions)

User Suggested Solutions

1. Unplugging and plugging back in

Community Discussions

stopped working

Unplugging and plugging back in resolved the issue temporarily.

DIY View on Reddit →

Source: Reddit r/appliancerepair