Maytag Oven Error CAL
⚡ Quick Answer: The Maytag Oven CAL error indicates that the oven's calibration feature is active. This mode allows for the calibration of the oven's temperature disp... ✅ DIY Fixable
What Does Error CAL Mean?
The Maytag Oven CAL error indicates that the oven's calibration feature is active. This mode allows for the calibration of the oven's temperature display and operation. During this time, the temperature display may show 'CAL' instead of the actual temperature, and the oven may not heat until the calibration process is completed or exited. It's not a fault but a normal function of the appliance.
Common Symptoms:
- Display shows 'CAL' instead of temperature or other codes
- Oven may not begin normal heating cycles until calibration is complete or exited
Possible Causes
- Oven calibration mode/feature active (high)
How to Fix Error CAL
DIY Fix Exit or complete oven calibration
- Refer to your specific oven model’s user manual for instructions on how to exit or complete the calibration procedure.
- Commonly, pressing a specified sequence of buttons (e.g., 'Bake' then 'Start') will accept or exit calibration.
- If unsure, power cycle the oven by turning off its circuit breaker for one minute, then restore power and observe if 'CAL' persists.
Technician Only Verify calibration settings and control board state
- Access service manual for the specific Maytag oven model to understand how the calibration feature is entered and exited.
- Check whether the control board is erroneously entering calibration mode due to a stuck key or faulty control panel.
- Test control panel buttons for proper function; replace if they are causing repeat unintended entries into calibration mode.
Parts needed: Control panel / membrane switch, Electronic control board
- If 'CAL' remains on display after following correct calibration exit steps and power cycling.
- If other error codes accompany 'CAL' or the oven fails to heat after calibration feature is exited.
Next step
Choose the next step for CAL
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Main Control Board
The central brain of the appliance that controls all components, cycles, and timings.
- Typical part-only price
- $120 - $280
- DIY difficulty
- Medium
- Estimated time
- 20-40 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Model-compatible Oven parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Non-Scratch Cooktop Cleaner
A routine surface-care product. Confirm that it is approved for the specific glass, ceramic, enamel, or stainless finish.
Oven Thermometer
A diagnostic aid for comparing cavity temperature during a controlled check. It does not prove which internal component has failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Technical Specifications
| wattage | |
|---|---|
| component | Temperature Sensor |
| resistance | 1000-1100 ohms |
| part_number | W10709960 |
| voltage_rating | 120V AC |
Common Questions
What does CAL error mean on Maytag Oven?
CAL indicates that the oven's calibration feature is active, impacting temperature display.
Can I fix Maytag Oven CAL error myself?
Yes, refer to your user manual to exit calibration or power cycle the oven.
How much does it cost to fix CAL error?
Estimated repair costs range from $50 to $300 depending on parts and labor.
When should I call a technician for CAL?
Call a technician if 'CAL' persists after exiting calibration or if other error codes appear.
Sources & References
Data last verified: 2026-07-22
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!