Beko Dishwasher: not spraying water from upper spray arm

Professional Repair Guide

What is this symptom?

If your Beko dishwasher runs but the upper spray arm isn't spraying water, your upper rack dishes may remain dirty while the lower ones are cleaned. This issue could stem from clogged spray arm holes, misalignment of the feed tube, or water pressure problems. Addressing this can restore proper cleaning performance to your dishwasher.

Urgency: Medium

Important Tips for Beko Models

Official Beko guidance includes specific steps to remove and clean the upper spray arm by undoing the nut and washing under tap water. (BEKOGLOBAL
Community repair guides for Beko indicate blocked or misaligned upper rack feed tube may contribute to upper rack not spraying. (BEKOGLOBAL

Possible Causes

Clogged upper spray arm holes/nozzles

How to Identify: Upper spray arm jets have visible debris or mineral buildup; water sprays weakly or not at all from upper arm while lower still works.

Part: Upper spray arm

Misaligned or blocked upper rack feed tube

How to Identify: Upper arm does not receive water although supply is present; possible misalignment of connecting tube.

Part: Upper rack feed tube (water supply to upper arm)

Insufficient water pressure or inlet issues

How to Identify: Dishwasher runs with weak overall spray; insufficient water pressure entering dishwasher.

Part: Inlet valve / water supply

Damaged or worn upper spray arm bearings/parts

How to Identify: Spray arm doesnâ€™t spin freely; visible wear/breaks.

Part: Upper spray arm bearing/arm

DIY Solutions

Clean upper spray arm and jets

Moderate 15â€“30 minutes

Tools Needed: screwdriver (if required), toothpick or small brush, vinegar or descaling solution

Turn off dishwasher and open door.
Remove upper rack to access spray arm.
Detach upper spray arm: usually unscrew nut or press tabs (follow Beko manual). (BEKOGLOBAL
Rinse arm under tap water and use a toothpick/brush to clear holes.
Soak arm in vinegar or descaling solution to dissolve mineral buildup.
Reinstall spray arm securely, replace rack, and run a test cycle.

⚠️ Safety First: Ensure power is off before removing parts

Check and realign upper rack feed tube

Advanced 20â€“40 minutes

Tools Needed: flashlight

Turn off dishwasher power and water supply.
Pull out upper rack fully.
Inspect water feed tube supplying upper arm for kinks, misalignment, or debris.
Carefully realign or clear blockage if visible.
Reinstall rack and test dishwasher.

⚠️ Safety First: Do not force parts; risk of breaking plastic components

Professional Repairs

Replace upper spray arm or feed components

Estimated Cost: $40â€“$120 (parts) plus labor

Inspect and repair water inlet or circulation system

Estimated Cost: $150â€“$400

When to Call a Professional

Upper spray arm cracked or stripped

Cleaning and feed tube checks do not restore spray

Water pressure issues persist affecting overall performance

Preventive Maintenance

Clean spray arms regularly: Clogs causing reduced or absent spray
Frequency: monthly
Inspect filters and remove debris: Food buildup reaching spray arms
Frequency: monthly

Frequently Asked Questions

Why is my Beko Dishwasher not spraying water from upper spray arm?

Common causes include clogged upper spray arm holes, misaligned feed tube, or insufficient water pressure.

How do I fix Beko Dishwasher not spraying water from upper spray arm myself?

Clean the upper spray arm and jets or check for misalignment in the feed tube.

How much does it cost to fix not spraying water from upper spray arm?

Professional repairs can range from $40â€“$120 for parts plus labor, or $150â€“$400 for inlet issues.

When should I call a technician for not spraying water from upper spray arm?

If DIY solutions don't work or you suspect a major issue, it's best to consult a professional.

References & Sources

How to fix dishwasher not spraying water (Beko) Official

Community Analytical Insights

Analysis based on real user discussions from appliance repair communities

Can I Fix This Myself?

70%

DIY Success Rate Difficulty: Either

Common Issues Reported by Users

Clogged upper spray arm due to food debris or mineral buildup
Blocked water inlet filter preventing proper water flow
Faulty or malfunctioning wash pump motor not generating sufficient pressure

User Suggested Solutions

Remove the upper spray arm and clean it thoroughly under running water to remove any debris or mineral buildup. Ensure the spray holes are clear.
Check and clean the water inlet filter located at the water supply connection. Remove any blockages that may be restricting water flow.
Inspect the wash pump motor for any signs of damage or malfunction. If necessary, replace the pump motor to restore proper pressure.