Beko Dishwasher Error F2
⚡ Quick Answer: The Beko dishwasher error F2 indicates a malfunction in the drain pump or water inlet valve, typically resulting in failure to drain water. Symptoms i... ✅ DIY Fixable
What Does Error F2 Mean?
The Beko dishwasher error F2 indicates a malfunction in the drain pump or water inlet valve, typically resulting in failure to drain water. Symptoms include stopping mid-cycle, improper water filling, and standing water in the tub. Common causes are a faulty water inlet valve or clogged drain/filter/hose.
Common Symptoms:
- Dishwasher stops mid‑cycle showing F2
- Water not filling properly or not draining
- Standing water visible in tub after cycle
Possible Causes
- Water inlet valve not operating correctly (medium)
- Clogged drain/filter/hose (community consensus from general dishwasher sources) (medium)
How to Fix Error F2
DIY Fix Check and clear basic water flow obstructions
- Turn off and unplug the dishwasher for safety.
- Remove and clean the dishwasher’s bottom filter and sump area.
- Check the drain hose for kinks or blockages; straighten or clear as needed.
- Ensure the water supply valve to the dishwasher is fully open.
DIY Fix Restart/reset the dishwasher
- Turn off the dishwasher at the mains or unplug it.
- Wait at least 5–10 minutes to allow internal systems to reset.
- Restore power and run a short cycle to see if F2 clears.
Technician Only Inspect/replace water inlet valve
- Verify correct operation of the water inlet valve solenoid and seating.
- Test valve coil and continuity with a multimeter.
- If faulty, replace the water inlet valve assembly.
Parts needed: water inlet valve, valve gasket/seals
Technician Only Diagnose pump and control inputs
- Access and test the drain pump for electrical continuity and proper rotation.
- Check float switch operation and water level sensor inputs.
- Inspect wiring connectors to control board related to inlet/drain sensing.
Parts needed: drain pump, float switch/sensors
- Error persists after clearing all visible clogs and resetting.
- Signs of water leakage or flooding from the machine base.
- No water enters but inlet components test good; electrical diagnostics needed.
Next step
Choose the next step for F2
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Water Inlet Valve
Controls the flow of hot and cold water into the appliance.
- Typical part-only price
- $25 - $60
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Drain Pump
Pumps waste water out of the appliance during the drain cycle.
Float Switch
Detects the maximum water level to prevent overflow and potential flooding.
Model-compatible Dishwasher parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Dishwasher Cleaner and Descaler
Supports routine removal of mineral scale, grease, and odor. It is maintenance, not a repair for a failed pump, valve, or control.
Braided Dishwasher Inlet Hose
For replacement of an externally damaged supply hose. Verify connection size, length, and appliance installation requirements before ordering.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Technical Specifications
| wattage | 30W |
|---|---|
| component | Drain Pump |
| resistance | 10-20 ohms |
| part_number | Beko 1740200200 |
| voltage_rating | 230V AC |
Common Questions
What does F2 error mean on Beko dishwasher?
F2 indicates a drain pump or water inlet valve malfunction, causing improper draining.
Can I fix Beko dishwasher F2 error myself?
Yes, check for clogs, clean filters, and reset the dishwasher to troubleshoot.
How much does it cost to fix F2 error?
Estimated repair costs range from $50 to $150 for parts, plus labor.
When should I call a technician for F2?
Call if the error persists after troubleshooting, or if there are signs of leakage.
Data last verified: 2026-07-25
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!