Beko Dishwasher Error E06
⚡ Quick Answer: The Beko dishwasher E06 error indicates a fault with the temperature sensor, which may be short-circuited or malfunctioning. This issue can cause the ... ✅ DIY Fixable
What Does Error E06 Mean?
The Beko dishwasher E06 error indicates a fault with the temperature sensor, which may be short-circuited or malfunctioning. This issue can cause the dishwasher to stop mid-cycle, fail to complete heating functions, and inaccurately sense water temperature, leading to drainage problems and unusual operational noises.
Common Symptoms:
- Dishwasher stops mid‑cycle with E06 shown
- Heating related functions not completed
- Dishwasher fails to correctly sense water temperature
Possible Causes
- Temperature sensor (thermistor) short circuit or internal fault (medium)
How to Fix Error E06
DIY Fix Basic checks before calling service
- Turn off the dishwasher and unplug at the mains.
- Wait several minutes and restore power to see if the error clears.
- Ensure the dishwasher completed drainage and that there are no water in the base tray (flood detection can interfere with sensors).
Technician Only Inspect/replace temperature probe and wiring
- Disconnect power to the dishwasher.
- Access the internal temperature sensor (thermistor) area inside the dishwasher tank.
- Check continuity and resistance of the temperature sensor to confirm short circuit or failure.
- Inspect wiring harness and connectors for damage or corrosion.
- Replace faulty NTC sensor or repair wiring as required.
- Test dishwasher through a full cycle to verify resolution.
Parts needed: NTC temperature sensor, Wiring harness / connectors
- If the error persists after basic power reset and dishwasher is stopping mid‑cycle.
- If internal components are suspected faulty or wiring appears damaged.
Next step
Choose the next step for E06
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Temperature Sensor
Monitors the internal temperature to ensure correct operation and prevent overheating.
- Typical part-only price
- $15 - $35
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Wiring Harness
Connects controls, sensors, motors, and other electrical components inside the appliance.
Model-compatible Dishwasher parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Dishwasher Cleaner and Descaler
Supports routine removal of mineral scale, grease, and odor. It is maintenance, not a repair for a failed pump, valve, or control.
Braided Dishwasher Inlet Hose
For replacement of an externally damaged supply hose. Verify connection size, length, and appliance installation requirements before ordering.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Technical Specifications
| wattage | 30W |
|---|---|
| component | Drain Pump |
| resistance | 10-20 ohms |
| part_number | Beko 1742000200 |
| voltage_rating | 230V AC |
Common Questions
What does E06 error mean on Beko dishwasher?
E06 indicates a temperature sensor fault, causing the dishwasher to stop mid-cycle and fail to complete heating.
Can I fix Beko dishwasher E06 error myself?
Yes, you can try basic troubleshooting like resetting the power and checking for drainage issues.
How much does it cost to fix E06 error?
Repair costs typically range from $50 to $150, depending on parts and labor.
When should I call a technician for E06?
Call a technician if the error persists after a reset, or if you suspect internal components are faulty.
Sources & References
Data last verified: 2026-07-25
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!