Indesit Dishwasher Error F10
⚡ Quick Answer: The Indesit Dishwasher error F10 indicates a fault in the heating system, likely involving the heating element or thermostat. This error usually resul... ✅ DIY Fixable
What Does Error F10 Mean?
The Indesit Dishwasher error F10 indicates a fault in the heating system, likely involving the heating element or thermostat. This error usually results in the cycle stopping mid-operation, with no heating of water, and can be accompanied by unusual noises. If the dishwasher fails to reach the set temperature, it's crucial to check for potential heating component failures.
Common Symptoms:
- Cycle stops and displays F10
- Dishwasher not heating water or not reaching temperature setpoint
- Possible mid‑cycle interruption
Possible Causes
- Faulty heating element (medium)
- Thermostat or temperature sensor issue (medium)
How to Fix Error F10
DIY Fix Basic user checks before service
- Turn off the dishwasher and unplug or isolate power for a few minutes, then restart to see if the error clears.
- Ensure the dishwasher door is fully closed and latched properly.
- Check that water supply is on and there are no obvious leaks or blockages in filters and spray arms.
Technician Only Inspect and replace heating components
- Disconnect the dishwasher from power.
- Access the heating element and measure resistance with a multimeter; verify continuity to check if the heating element is faulty.
- Test the thermostat and temperature sensors for correct operation and continuity.
- Replace the defective heating element or thermostat as needed and reassemble the dishwasher.
- Run a test cycle to confirm the error F10 is resolved.
Parts needed: Heating element, Thermostat/temperature sensor
- If the F10 error persists after basic user checks and power cycling
- If there are signs of water leakage, burning smells, or electrical issues
Next step
Choose the next step for F10
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Heating Element
Heats the water or air inside the appliance to the required temperature.
- Typical part-only price
- $40 - $95
- DIY difficulty
- Medium
- Estimated time
- 30-45 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Thermostat
Regulates temperature by turning the heating or cooling system on or off.
Temperature Sensor
Monitors the internal temperature to ensure correct operation and prevent overheating.
Model-compatible Dishwasher parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Dishwasher Cleaner and Descaler
Supports routine removal of mineral scale, grease, and odor. It is maintenance, not a repair for a failed pump, valve, or control.
Braided Dishwasher Inlet Hose
For replacement of an externally damaged supply hose. Verify connection size, length, and appliance installation requirements before ordering.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Technical Specifications
| wattage | 30W |
|---|---|
| component | Drain Pump |
| resistance | 10-15 ohms |
| part_number | C00143010 |
| voltage_rating | 230V AC |
Common Questions
What does F10 error mean on Indesit Dishwasher?
F10 indicates a heating system fault, typically involving the heating element or thermostat.
Can I fix Indesit Dishwasher F10 error myself?
Yes, start by power cycling the unit and ensuring the door is closed. Check for water supply and blockages.
How much does it cost to fix F10 error?
Repair costs range from $80 to $250, depending on parts and labor.
When should I call a technician for F10?
Call a technician if the error persists after basic checks or if you notice leaks or burning smells.
Sources & References
Data last verified: 2026-07-22
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!