Hoover Washing Machine Error E11
⚡ Quick Answer: The Hoover washing machine E11 error indicates a malfunction related to the water inlet valve or a drying sensor/thermistor fault, particularly in com... ✅ DIY Fixable
What Does Error E11 Mean?
The Hoover washing machine E11 error indicates a malfunction related to the water inlet valve or a drying sensor/thermistor fault, particularly in combo washer-dryer models. Users may experience the machine halting mid-cycle, the drying function failing, or difficulties with the door locking properly. This error can lead to the unit not filling with water or completing drying cycles as expected.
Common Symptoms:
- Machine stops mid-cycle with E11 displayed or LED blinking E11 pattern
- Drying function (on combo washer-dryer models) fails and/or won’t complete
- Door may not lock or start cycle in some community reports
Possible Causes
- Drying sensor (thermistor) fault or open circuit on washer-dryer models (medium)
- Damaged wiring to dryer sensor/thermistor (medium)
- Door lock feedback signal error (conflicting community repair guide) (low)
How to Fix Error E11
DIY Fix Power cycle and basic checks
- Disconnect the machine from mains power for 10–15 minutes and reconnect to reset temporary faults.
- If your model has a drying function, reduce load size and retry a cycle to see if E11 recurs.
- Ensure the door fully closes and latches before starting a cycle.
Technician Only Inspect and replace dryer thermistor/sensor and wiring
- Disconnect power and remove top panel to access internal components.
- Locate the dryer sensor/thermistor and inspect wiring for broken or worn connections.
- Test sensor resistance with a multimeter; compare against expected values for your model.
- Replace the sensor and any damaged wiring harness as needed.
- Reassemble and test the machine.
Parts needed: Dryer sensor/thermistor, Wiring harness/connectors
Technician Only Check door lock feedback circuitry (if relevant to model)
- Test door lock interlock and feedback signal wiring with a multimeter.
- Replace door lock assembly or repair wiring if continuity issues are found.
- Verify control board input for correct feedback signal.
Parts needed: Door lock assembly, Associated wiring harness
- If error persists after power cycling and basic checks
- If internal component testing or replacement is required and you lack experience with appliance repair
- If multiple error codes appear concurrently indicating control board issues
Next step
Choose the next step for E11
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Thermistor
Measures precise temperature changes and sends resistance feedback to the control board.
- Typical part-only price
- $15 - $35
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Wiring Harness
Connects controls, sensors, motors, and other electrical components inside the appliance.
Door Lock Assembly
Secures the door shut during operation for safety and signals the control board to run.
Model-compatible Washing Machine parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Washing Machine Cleaner Tablets
Routine tub-cleaning supplies for residue and odor control. They do not repair a mechanical, drainage, or electronic fault.
Braided Washer Inlet Hoses
A maintenance replacement option for visibly worn external fill hoses. Verify thread size, length, and hot/cold connection requirements.
Washer Drain Hose Holder
Helps secure an external drain hose at the standpipe. It does not correct an internal pump or control fault.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Technical Specifications
| wattage | 50W |
|---|---|
| component | Water Inlet Valve |
| resistance | 500-1500 ohms |
| part_number | Hoover 31005467 |
| voltage_rating | 230V AC |
Common Questions
What does E11 error mean on hoover washing machine?
E11 indicates a water inlet valve issue or a drying sensor fault, causing the machine to stop mid-cycle.
Can I fix hoover washing machine E11 error myself?
Yes, try power cycling the machine, reducing load size, and ensuring the door fully closes before starting a cycle.
How much does it cost to fix E11 error?
Estimated repair cost is $40–$120 for parts, excluding labor.
When should I call a technician for E11?
Call a technician if the error persists after basic checks or if you need to replace internal components.
Sources & References
Data last verified: 2026-07-25
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!