Frigidaire Oven Error F13
⚡ Quick Answer: The F13 error code on your Frigidaire oven indicates a malfunction in the temperature sensor or a failure in the main control board's EEPROM. This err... ✅ DIY Fixable
What Does Error F13 Mean?
The F13 error code on your Frigidaire oven indicates a malfunction in the temperature sensor or a failure in the main control board's EEPROM. This error typically results in erratic temperature readings, the oven not heating properly, or unresponsive controls. If the error persists after a power reset, it may point to a communication fault between the keypad and the control board, necessitating further inspection or replacement.
Common Symptoms:
- Oven display shows F13 error and oven functions stop
- Error persists after power-reset
- Buttons may be unresponsive or control panel doesn’t control heating
Possible Causes
- EEPROM failure on main control board (E prompt failure) (high)
- Keypad to control board communication fault (medium)
How to Fix Error F13
DIY Fix Power-cycle the oven to clear temporary memory errors
- Turn off the oven and disconnect from power by unplugging or turning off the circuit breaker
- Wait at least 30 seconds to allow internal capacitors to discharge
- Restore power and attempt to clear the error and use the oven normally
Technician Only Inspect and repair communication connections between keypad and control board
- Disconnect power to the oven
- Remove back/control panel to access the keypad ribbon and control board connectors
- Inspect and reseat connectors, clean corrosion if present
- Test communication and replace damaged ribbon or connector as necessary
Parts needed: Keypad/display ribbon cable, Connectors
Technician Only Replace main control board (Electronic Oven Control)
- Disconnect all power to the oven
- Remove control panel or rear panel to access the EOC board
- Record and disconnect all wire harnesses from the old board
- Install the correct replacement board for the specific model
- Reconnect all wiring and restore power to test functionality
Parts needed: Main control board (Electronic Oven Control)
- Error persists after power reset and basic connector inspection
- You are not comfortable working with internal electrical components
Next step
Choose the next step for F13
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Ribbon Cable
Carries low-voltage signals between a user interface, display, and electronic control board.
- Typical part-only price
- $10 - $80
- DIY difficulty
- Medium
- Estimated time
- 20-60 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Main Control Board
The central brain of the appliance that controls all components, cycles, and timings.
Model-compatible Oven parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Non-Scratch Cooktop Cleaner
A routine surface-care product. Confirm that it is approved for the specific glass, ceramic, enamel, or stainless finish.
Oven Thermometer
A diagnostic aid for comparing cavity temperature during a controlled check. It does not prove which internal component has failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Technical Specifications
| wattage | |
|---|---|
| component | Temperature Sensor |
| resistance | 1000-1100 ohms |
| part_number | 316217002 |
| voltage_rating | 120V AC |
Common Questions
What does F13 error mean on frigidaire oven?
F13 indicates a malfunction in the temperature sensor or control board, leading to heating issues.
Can I fix frigidaire oven F13 error myself?
Yes, you can try power-cycling the oven to clear temporary errors.
How much does it cost to fix F13 error?
Estimated repair costs range from $20 to $100 for basic fixes.
When should I call a technician for F13?
Call a technician if the error persists after power reset or if you're uncomfortable with electrical components.
Sources & References
Data last verified: 2026-07-25
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!