Frigidaire Dishwasher Error I10

⚡ Quick Answer: The Frigidaire dishwasher error I10 indicates an issue with the water inlet valve, preventing the dishwasher from filling with water. This error may o... ✅ DIY Fixable

What Does Error I10 Mean?

The Frigidaire dishwasher error I10 indicates an issue with the water inlet valve, preventing the dishwasher from filling with water. This error may occur when the dishwasher fails to fill within a set time, leading to early cycle termination or insufficient water in the tub. Common causes include an insufficient water supply, clogged or kinked inlet hoses, or a faulty water inlet valve.

Common Symptoms:

  • Dishwasher stops early or doesn’t start a full cycle
  • No or insufficient water seen in tub during fill
  • Dishwasher may beep and display i10 immediately when attempting to start

Possible Causes

  • Insufficient water supply to dishwasher (high)
  • Clogged or kinked inlet hose (medium)
  • Faulty water inlet valve (medium)

How to Fix Error I10

DIY Fix Check and restore water supply

  1. Ensure water supply valve under sink is fully open
  2. Inspect visible inlet hose for kinks or bends and straighten
  3. Check that faucet supplying dishwasher isn’t partially off

Technician Only Inspect inlet components and test valve

  1. Disconnect dishwasher power and water supply
  2. Remove and inspect the inlet hose and clean debris
  3. Test inlet valve for proper operation and replace if defective
  4. Verify water pressure meets manufacturer specifications
  5. Check water level sensor function if available

Parts needed: Water inlet valve, Inlet hose, Pressure sensor/air trap (if applicable)

🛑 When to Call a Pro:
  • If water supply and hose checks do not resolve the error
  • If inlet valve tests show failure
  • If internal sensors or control board may be at fault

Next step

Choose the next step for I10

Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.

Based on diagnostic data

Most relevant component to inspect

Water Inlet Valve

Controls the flow of hot and cold water into the appliance.

Typical part-only price
$25 - $60
DIY difficulty
Easy
Estimated time
15-30 mins
Where can I find the model number?

Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.

Find a part that fits my model

Verify the complete model and part number on the retailer's compatibility page before ordering.

Other parts options

Check related components first; use model search as a fallback.

Model number required

Model-compatible Dishwasher parts

Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.

Find a part that fits my model

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.

Optional routine care

Maintenance supplies

These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.

Maintenance supply

Dishwasher Cleaner and Descaler

Supports routine removal of mineral scale, grease, and odor. It is maintenance, not a repair for a failed pump, valve, or control.

View maintenance supply
Maintenance supply

Braided Dishwasher Inlet Hose

For replacement of an externally damaged supply hose. Verify connection size, length, and appliance installation requirements before ordering.

View maintenance supply

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.

Technical Specifications

wattage 30W
component Water Inlet Valve
resistance 10-20 ohms
part_number 154567401
voltage_rating 120V AC

Common Questions

What does I10 error mean on frigidaire dishwasher?

The I10 error indicates a problem with the water inlet valve, causing the dishwasher to not fill properly.

Can I fix frigidaire dishwasher I10 error myself?

Yes, check the water supply and inlet hose for kinks or blockages.

How much does it cost to fix I10 error?

Repair costs range from $50 to $200 depending on the issue.

When should I call a technician for I10?

Call if self-checks don't resolve the issue or if the inlet valve tests fail.

Sources & References

Data last verified: 2026-07-25

User Comments (0)

Share your experience or solution below.

Be the first to comment!