Maytag Washing Machine: tub shaking during spin cycle
What is this symptom?
Is your Maytag washing machine tub shaking excessively during the spin cycle? This common issue can lead to loud noises and even movement across the floor. Typically caused by an unbalanced load, a level washer, or worn parts, it’s important to address this problem promptly to avoid further damage.
Important Tips for Maytag Models
- Maytag washers with Advanced Vibration Control use stronger shock absorbers to minimize vibration; proper installation and leveling are emphasised in manufacturer guidance.
Possible Causes
Unbalanced or uneven laundry load
How to Identify: Washer improves when clothes are redistributed evenly; heavy/bulky items cluster to one side.
Part: Drum and load distribution
Washer not level on the floor
How to Identify: Washer rocks when pushed slightly; a spirit level shows non‑level front to back or side to side.
Part: Leveling feet/installation
Worn or damaged shock absorbers/dampeners
How to Identify: Persistent vibration even with balanced load and level surface; audible thumping or heavy motion during spin.
Part: Shock absorbers
Broken or weakened suspension rods/springs/counterbalance springs
How to Identify: Machine still vibrates despite correct leveling and balanced load; springs visibly worn/broken upon inspection. (Appliance Parts Pros
Part: Suspension rods/springs/counterbalance springs
Transit bolts not removed after delivery
How to Identify: Recent installation/move and machine shakes violently at first use; transit bolts are present at rear.
Part: Transit bolts
DIY Solutions
Redistribute and balance laundry load
- Open washer and remove clothes.
- Rearrange laundry so heavy items are evenly distributed around the drum.
- Avoid washing single heavy items alone; add similar weight items if needed.
- Restart spin cycle to check if vibration reduces.
Level the washer
- Place spirit level on top of washer side‑to‑side and front‑to‑back.
- Adjust each leveling foot by turning clockwise to raise or counter‑clockwise to lower until level is achieved.
- Tighten lock nuts on the feet if present.
- Test with a spin cycle to confirm stability.
Next step
Choose the next step for tub shaking during spin cycle
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Washer Shock Absorber
Dampens tub movement and vibration during high-speed spin cycles.
- Typical part-only price
- $25 - $100
- DIY difficulty
- Medium
- Estimated time
- 45-90 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Washer Suspension Rod Kit
Supports and stabilizes the washer tub during agitation and spin.
Model-compatible Washing Machine parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Washing Machine Cleaner Tablets
Routine tub-cleaning supplies for residue and odor control. They do not repair a mechanical, drainage, or electronic fault.
Braided Washer Inlet Hoses
A maintenance replacement option for visibly worn external fill hoses. Verify thread size, length, and hot/cold connection requirements.
Washer Drain Hose Holder
Helps secure an external drain hose at the standpipe. It does not correct an internal pump or control fault.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Professional Repairs
Replace shock absorbers/dampeners
Replace suspension rods/springs/counterbalance springs
When to Call a Professional
Preventive Maintenance
-
Ensure washer is level: Excessive vibration during cycles
Frequency: initial setup and annual check -
Distribute laundry evenly: Unbalanced load caused vibration
Frequency: Every wash -
Inspect suspension components: Wear‑induced vibration and internal stress
Frequency: Annual
Frequently Asked Questions
Why is my Maytag Washing Machine tub shaking during spin cycle?
How do I fix Maytag Washing Machine tub shaking during spin cycle myself?
How much does it cost to fix tub shaking during spin cycle?
When should I call a technician for tub shaking during spin cycle?
References & Sources
Community Analytical Insights
Guidance from available sources; statistical claims are shown only for samples of at least 10 discussions
Common Issues Reported by Users
- Unbalanced load in the washing machine
- Worn or damaged suspension springs
- Faulty shock absorbers
User Suggested Solutions
-
Redistribute the laundry evenly in the tub. Remove items if necessary to balance the load.
-
Inspect and replace worn or damaged suspension springs. This involves removing the front panel and accessing the springs.
-
Check and replace faulty shock absorbers. Ensure to disconnect the power and water supply before starting this repair.
Limited-source guidance; percentages and success-rate claims are not shown
View
Sources
Data compiled from real discussions on r/appliancerepair and r/Appliances:
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!