Maytag Washing Machine: not filling properly

Possible Causes

Water supply valves closed or water supply issue

How to Identify: No water entering the washer even though cycle started; check that hot and cold supply valves are fully open and water is available at house taps.

Part: Household water supply valves, inlet hoses

Kinked or improperly connected inlet hoses

How to Identify: Hoses bent, crushed, or not securely connected; water flow restricted before washer.

Part: Inlet hoses

Clogged inlet screens/filters

How to Identify: Water flows from home taps but little or no water enters washer; debris visible at hose connections screens.

Part: Inlet screens/filters on water hoses

DIY Solutions

Ensure water supply valves are fully open

Easy 5 minutes

1. Locate hot and cold water supply valves behind washer.
2. Turn both valves fully counter‑clockwise to open.
3. Run a quick rinse to test water flow into washer.

⚠️ Safety First: Ensure faucets are fully off before adjusting.

Straighten and reconnect inlet hoses

Easy 10 minutes

Tools Needed: Adjustable wrench

1. Turn off water supply valves.
2. Use wrench to loosen hose connections at washer and faucets.
3. Remove kinks and inspect hoses for damage.
4. Reconnect hoses snugly and turn valves back on to test.

⚠️ Safety First: Do not overtighten fittings to avoid damage.

Clean inlet screens/filters

Moderate 15–30 minutes

Tools Needed: Small brush, Bucket, Towel

1. Turn off water supply valves.
2. Disconnect inlet hoses from washer.
3. Inspect small mesh screens at hose connections; use brush to remove debris.
4. Reattach hoses and restore water supply; test fill.

⚠️ Safety First: Have towel ready for residual water.

Next step

Choose the next step for not filling properly

Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.

Model number required

Browse by model — no specific failed part is claimed

Model-compatible Washing Machine parts

Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.

Enter your complete model number for compatible results

Apply

Where can I find the model number?

Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.

Find a part that fits my model

Search results are not a diagnosis. Verify both the complete appliance model and the retailer's fit information before ordering.

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.

Optional routine care

Maintenance supplies

These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.

Maintenance supply

Washing Machine Cleaner Tablets

Routine tub-cleaning supplies for residue and odor control. They do not repair a mechanical, drainage, or electronic fault.

View maintenance supply

Maintenance supply

Braided Washer Inlet Hoses

A maintenance replacement option for visibly worn external fill hoses. Verify thread size, length, and hot/cold connection requirements.

View maintenance supply

Maintenance supply

Washer Drain Hose Holder

Helps secure an external drain hose at the standpipe. It does not correct an internal pump or control fault.

View maintenance supply

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.

Professional Repairs

Replace pressure switch or pressure tube

Estimated Cost: $50–$120

Replace water inlet valve assembly

Estimated Cost: $60–$150

When to Call a Professional

If water still does not fill after checking supply, hoses, and cleaning filters

If internal components like pressure switch or inlet valve are suspected faulty

If you are not comfortable disassembling parts of the washer

Preventive Maintenance

• Clean inlet screens regularly: Reduced water flow due to debris buildup
  Frequency: annually
• Inspect hoses for kinks or wear: Restricted water flow
  Frequency: quarterly

Frequently Asked Questions

Why is my Maytag Washing Machine not filling properly?

Common causes include closed water supply valves, kinked inlet hoses, or clogged inlet screens.

How do I fix Maytag Washing Machine not filling properly myself?

Ensure water valves are open, straighten inlet hoses, and clean inlet screens for quick fixes.

How much does it cost to fix not filling properly?

Professional repairs for this issue typically cost between $50 and $150, depending on the problem.

When should I call a technician for not filling properly?

Call a technician if DIY solutions don't resolve the issue, or if you suspect a faulty pressure switch or inlet valve.

References & Sources

• Not Filling or Long Fill - Washer - Maytag Official

Common Issues Reported by Users

• Faulty inlet valves (2 mentions)
• Control board issues (1 mentions)

User Suggested Solutions

1. Check and replace faulty inlet valves

2. Inspect control board for faults