Maytag Washing Machine: not draining during second spin cycle
What is this symptom?
Is your Maytag washing machine not draining during the second spin cycle? If water remains in the drum after the wash cycle, it could be due to a clogged drain pump, a faulty drain pump, or a lid switch failure. Understanding the causes can help you troubleshoot effectively.
Important Tips for Maytag Models
- Maytag models may include a coin trap/filter near the pump—check and clean if present
Possible Causes
Clogged drain pump or drain hose
How to Identify: Standing water remains; washer stops before/during spin; gurgling sounds; water drains slowly or not at all
Part: Drain pump and drain hose
Faulty drain pump
How to Identify: Pump makes unusual noises, no water movement during drain phase, or motor hum without draining
Part: Drain pump
Lid switch or door latch failure
How to Identify: Washer won’t detect closed lid; no click when closing; machine won’t proceed to spin or drain properly
Part: Lid switch (top-load) / door latch (front-load)
DIY Solutions
Clear drain hose and pump blockages
- Disconnect washer power and move away from wall
- Detach and inspect drain hose for kinks/clogs; use a brush to clear obstructions
- Access drain pump (bottom/back) and remove debris from pump inlet/impeller
- Reattach hose and test drain/spin cycle
Test and replace lid switch (top-load)
- Unplug washer and access lid switch assembly
- Test continuity with multimeter while closing lid
- Replace switch if continuity absent or visibly damaged
- Reassemble and test washer
Next step
Choose the next step for not draining during second spin cycle
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Drain Hose
Carries waste water from the drain pump to your home's standpipe or sink drain.
- Typical part-only price
- $15 - $30
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Drain Pump
Pumps waste water out of the appliance during the drain cycle.
Door Latch Assembly
Mechanically secures the appliance door and may operate a door-closed safety switch.
Door or Lid Switch
Detects whether the appliance door or lid is safely closed before operation.
Model-compatible Washing Machine parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Washing Machine Cleaner Tablets
Routine tub-cleaning supplies for residue and odor control. They do not repair a mechanical, drainage, or electronic fault.
Braided Washer Inlet Hoses
A maintenance replacement option for visibly worn external fill hoses. Verify thread size, length, and hot/cold connection requirements.
Washer Drain Hose Holder
Helps secure an external drain hose at the standpipe. It does not correct an internal pump or control fault.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Professional Repairs
Replace drain pump
Control board/timer replacement
Motor or drive system repair
When to Call a Professional
Preventive Maintenance
-
Clean drain hose & pump filter: Clog-related drainage and spin issues
Frequency: annually -
Check lid switch function: Spin cycle interruptions due to safety sensor failure
Frequency: semi-annually
Frequently Asked Questions
Why is my Maytag Washing Machine not draining during second spin cycle?
How do I fix Maytag Washing Machine not draining during second spin cycle myself?
How much does it cost to fix not draining during second spin cycle?
When should I call a technician for not draining during second spin cycle?
References & Sources
Community Analytical Insights
Guidance from available sources; statistical claims are shown only for samples of at least 10 discussions
Common Issues Reported by Users
- Clogged drain hose or pump filter
- Faulty lid switch preventing drain cycle
- Malfunctioning drain pump
User Suggested Solutions
-
Check and clear the drain hose and pump filter. Step 1: Unplug the washing machine. Step 2: Locate the drain hose at the back of the machine, disconnect it, and check for clogs. Step 3: Access the pump filter (usually located at the front bottom of the machine), remove it, and clean any debris. Step 4: Reassemble and plug the machine back in.
-
Test the lid switch for functionality. Step 1: Unplug the machine. Step 2: Locate the lid switch (typically at the hinge area). Step 3: Use a multimeter to check for continuity when the lid is closed. If no continuity, replace the lid switch. Step 4: Reassemble and test the machine.
-
Inspect and replace the drain pump if necessary. Step 1: Unplug the washing machine. Step 2: Access the drain pump (usually located at the bottom of the machine). Step 3: Check for blockages or damage. If faulty, replace the pump with a new one. Step 4: Reassemble and test the machine.
Limited-source guidance; percentages and success-rate claims are not shown
View
Sources
Data compiled from real discussions on r/appliancerepair and r/Appliances:
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!