Maytag Washing Machine: adding water during spin
What is this symptom?
Experiencing unexpected water filling during the spin cycle of your Maytag washing machine? This unusual behavior can disrupt your laundry routine, indicating a potential issue with the water level sensor, inlet valve, or drain system.
Important Tips for Maytag Models
- Maytag models like MVWC565FW1 reported inlet valve/pressure switch issues leading to filling during spin
Possible Causes
Faulty water level sensor / pressure switch
How to Identify: Machine signals low water level, repeatedly adds water during spin or overfills; pressure switch air tube blockage signs
Part: Water level sensor (pressure switch)
Stuck or defective water inlet valve
How to Identify: Water continues entering even when it should be off; machine fills during spin; testing shows valve not closing
Part: Water inlet valve
Control board malfunction
How to Identify: Erratic cycle behavior, incorrect signals to inlet valve; visible damage on board or power tests fail
Part: Main control board
Drain blockage / pump failure leading to backflow
How to Identify: Water not draining properly; water remains and appears to be being added during spin; clogs seen
Part: Drain pump / drain hose
DIY Solutions
Inspect and clean pressure switch air tube
- Unplug washer and access the pressure switch tube (usually behind control panel)
- Check for kinks or clogs in the tube and clear any debris
- Reassemble and run a test cycle
Test and replace water inlet valve
- Unplug washer and shut off water supply
- Access rear panel to locate water inlet valve
- Use multimeter to test solenoid continuity; replace if defective
- Reassemble and restore water/power
Clear drain pump and hose blockage
- Unplug machine and locate drain pump access
- Place towels and bucket to catch water
- Remove debris from pump filter and drain hose
- Reassemble and test
Next step
Choose the next step for adding water during spin
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Pressure Switch
Detects the water level inside the tub and signals when to start or stop filling.
- Typical part-only price
- $25 - $65
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Water Inlet Valve
Controls the flow of hot and cold water into the appliance.
Main Control Board
The central brain of the appliance that controls all components, cycles, and timings.
Drain Hose
Carries waste water from the drain pump to your home's standpipe or sink drain.
Model-compatible Washing Machine parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Washing Machine Cleaner Tablets
Routine tub-cleaning supplies for residue and odor control. They do not repair a mechanical, drainage, or electronic fault.
Braided Washer Inlet Hoses
A maintenance replacement option for visibly worn external fill hoses. Verify thread size, length, and hot/cold connection requirements.
Washer Drain Hose Holder
Helps secure an external drain hose at the standpipe. It does not correct an internal pump or control fault.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Professional Repairs
Replace pressure switch/air dome assembly
Replace main control board
When to Call a Professional
Preventive Maintenance
-
Clean pressure switch air tube and drain pump filter: Improper water level detection and drain clogs
Frequency: annually -
Check inlet valve screens: Debris‑induced inlet valve malfunction
Frequency: every 6 months
Frequently Asked Questions
Why is my Maytag Washing Machine adding water during spin?
How do I fix Maytag Washing Machine adding water during spin myself?
How much does it cost to fix adding water during spin?
When should I call a technician for adding water during spin?
Community Analytical Insights
Guidance from available sources; statistical claims are shown only for samples of at least 10 discussions
Common Issues Reported by Users
- Unbalanced load causing the machine to add water for balancing
- Faulty pressure switch not detecting water level correctly
- Clogged or malfunctioning drain pump causing water retention
User Suggested Solutions
-
Redistribute the load evenly in the drum. Open the lid, rearrange the clothes, and run the spin cycle again.
-
Inspect and replace the pressure switch if faulty. Disconnect power, locate the pressure switch, and test with a multimeter. Replace if necessary.
-
Check the drain pump for clogs or damage. Remove the drain pump, clean out any debris, and test for functionality. Replace if needed.
Limited-source guidance; percentages and success-rate claims are not shown
View
Sources
Data compiled from real discussions on r/appliancerepair and r/Appliances:
Community Discussions
adding water during spin cycle
The issue may be related to the leveling feature, which causes the machine to add water to balance the load.
Source: Reddit r/appliancerepair
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!