Frigidaire Dishwasher: not spraying

Professional Repair Guide

What is this symptom?

If your Frigidaire dishwasher is running but not spraying water through the spray arms, dishes may remain unclean. This issue can stem from clogged spray arms, a blocked filter, or a faulty water inlet valve. Addressing these problems promptly ensures your dishwasher operates efficiently and your dishes are properly cleaned.

Urgency: Medium

Important Tips for Frigidaire Models

  • Resetting the dishwasher by unplugging power for 5 minutes and holding start button may clear issues; also ensure not to overload racks which can block spray arms.

Possible Causes

Clogged spray arms

How to Identify: Spray arm holes are blocked with food debris or mineral buildup and arms don’t spin freely.

Part: Spray arms

Blocked or dirty filter

How to Identify: Filter at bottom of dishwasher clogged with food debris, reducing water flow.

Part: Filter assembly

Faulty/blocked water inlet valve

How to Identify: Dishwasher not filling adequately; low water supply into dishwasher.

Part: Water inlet valve

Malfunctioning circulation pump or motor

How to Identify: Dishwasher fills but pump fails to drive water to spray arms; unusual noises observed.

Part: Circulation pump

Low water pressure supply

How to Identify: Inadequate home water pressure or kinked supply hose affecting dishwasher fill.

Part: Household water supply/pressure

DIY Solutions

Clean spray arms

Moderate 20-40 minutes
Tools Needed: screwdriver, toothpick or small brush
  1. Turn off dishwasher and remove bottom rack.
  2. Detach spray arms according to model instructions.
  3. Rinse spray arms under warm water and clear holes with a toothpick or brush.
  4. Reinstall spray arms and run a test cycle.
⚠️ Safety First: Ensure power is off before disassembly.

Clean filters

Easy 10-20 minutes
Tools Needed: warm water, soft brush
  1. Remove bottom rack and access filter assembly.
  2. Lift out filter and rinse under running water.
  3. Use a brush to remove stubborn debris.
  4. Reinstall filter securely and run a short cycle.
⚠️ Safety First: Avoid damaging filter mesh.

Professional Repairs

Replace water inlet valve

Estimated Cost: $50 - $150

Service circulation pump/motor

Estimated Cost: $150 - $400

When to Call a Professional

Dishwasher fills with water but still no spray after cleaning spray arms and filters
Unusual noises from motor/pump
Suspected electrical issues or part replacements beyond DIY skills

Preventive Maintenance

  • Clean spray arms and filters: Clogs that can stop water spraying
    Frequency: monthly
  • Inspect water supply line: Low water flow due to kinks or blockage
    Frequency: annually

Frequently Asked Questions

Why is my Frigidaire Dishwasher not spraying?
Common causes include clogged spray arms, blocked filters, or a faulty water inlet valve.
How do I fix Frigidaire Dishwasher not spraying myself?
Clean spray arms by rinsing them and clearing holes; also clean the filter for better water flow.
How much does it cost to fix not spraying?
Professional repairs can range from $50 to $150 for replacing the water inlet valve, or $150 to $400 for servicing the pump.
When should I call a technician for not spraying?
If DIY solutions don’t resolve the issue or if the problem is complex, it's best to consult a technician.

References & Sources

Community Analytical Insights

Analysis based on real user discussions from appliance repair communities

Can I Fix This Myself?

100%
DIY Success Rate Difficulty: DIY

Common Issues Reported by Users

  • Insufficient water supply (1 mentions)

User Suggested Solutions

  1. Replaced the water inlet valve, which was not filling enough water.

    Success rate: 50.0%
Analysis based on 2 community discussions
View Sources

Data compiled from real discussions on r/appliancerepair and r/Appliances:

  1. Frigidaire Dishwasher Sprayers not turning.
  2. Frigidaire dishwasher top spray arm not working

Community Discussions

Sprayers not turning, dishes not getting cleaned, soap pack not dissolving

Replaced the water inlet valve, which was not filling enough water.

DIY View on Reddit →

Source: Reddit r/appliancerepair

User Comments (0)

Share your experience or solution below.

Be the first to comment!