Frigidaire Dishwasher: not completing cycle

Possible Causes

Faulty or misaligned door latch / door switch

How to Identify: Dishwasher stops mid‑cycle and may beep; door doesn’t feel fully latched or closes loosely.

Part: Door latch / door switch

DIY Solutions

Check and Secure Door Latch

Easy 5-15 minutes

Tools Needed: none

1. Open the dishwasher door and inspect the latch for debris or misalignment.
2. Clean any debris and ensure the latch engages cleanly when door closes.
3. Close door firmly and restart dishwasher to confirm cycle completes.

⚠️ Safety First: Ensure door closes securely before using dishwasher.

Clean Filters and Check Drainage

Moderate 15-30 minutes

Tools Needed: screwdriver (if needed to access filter)

1. Turn off dishwasher and remove bottom rack.
2. Locate filter assembly at bottom of tub and twist/unscrew to remove.
3. Rinse filter under running water to clear debris.
4. Inspect drain hose at back for kinks and straighten if needed.
5. Run a rinse cycle to confirm proper drainage.

⚠️ Safety First: Unplug power before pulling drain hose.

Reset Control System

Easy 5-10 minutes

Tools Needed: none

1. Press and hold the Cancel/Start button for ~3 seconds until lights flash.
2. If no effect, turn off the dishwasher circuit breaker for 5 minutes.
3. Restore power and start a new cycle.

⚠️ Safety First: Turning off breaker cuts power; ensure no water is standing inside.

Check Water Supply Valve

Easy 5 minutes

Tools Needed: none

1. Locate water supply valve under sink.
2. Ensure valve is fully open.
3. Restart cycle to check if dishwasher fills and completes cycle.

⚠️ Safety First: No tools beyond ensuring valve position.

Next step

Choose the next step for not completing cycle

Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.

Based on diagnostic data

Most relevant component to inspect

Door or Lid Switch

Detects whether the appliance door or lid is safely closed before operation.

Typical part-only price

$15 - $55

DIY difficulty

Medium

Estimated time

20-45 mins

Optional: enter your model number

Apply

Where can I find the model number?

Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.

Find a part that fits my model

Verify the complete model and part number on the retailer's compatibility page before ordering.

Other parts options

Check related components first; use model search as a fallback.

Model number required

Model-compatible Dishwasher parts

Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.

Find a part that fits my model

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.

Optional routine care

Maintenance supplies

These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.

Maintenance supply

Dishwasher Cleaner and Descaler

Supports routine removal of mineral scale, grease, and odor. It is maintenance, not a repair for a failed pump, valve, or control.

View maintenance supply

Maintenance supply

Braided Dishwasher Inlet Hose

For replacement of an externally damaged supply hose. Verify connection size, length, and appliance installation requirements before ordering.

View maintenance supply

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.

Professional Repairs

Replace Door Latch or Switch

Estimated Cost: $100 - $200

Replace Control Board or Touchpad

Estimated Cost: $200 - $400

Replace Water Inlet Valve

Estimated Cost: $150 - $300

When to Call a Professional

Dishwasher shows error codes unresolvable by DIY resets

Dishwasher stops mid‑cycle and shows no response after resetting power and cleaning filters

Visible electrical issues (sparking, burning smell)

Preventive Maintenance

• Clean the filter and drain area: Drain clogs causing mid‑cycle stops
  Frequency: monthly
• Inspect door seal and latch: Door signal failures stopping cycles
  Frequency: monthly

Frequently Asked Questions

Why is my Frigidaire Dishwasher not completing cycle?

Common causes include a faulty door latch, misaligned door switch, or issues with the control board.

How do I fix Frigidaire Dishwasher not completing cycle myself?

Check the door latch, clean filters, reset the control system, and ensure the water supply valve is open.

How much does it cost to fix not completing cycle?

Professional repairs range from $100 to $400, depending on whether you need to replace the door latch, control board, or water inlet valve.

When should I call a technician for not completing cycle?

If DIY fixes don't resolve the issue or if the problem involves complex components, it's time to call a technician.

Common Issues Reported by Users

• Faulty circulation pump (1 mentions)

User Suggested Solutions

1. Replace circulation pump

Community Discussions

Dishwasher isn't working. The unit powers on, starts the cycle, water fills, and heats. Halfway through the cycle, it stops with a faint buzzing sound and the pump is hot.

The circulation pump went bad and was replaced.

DIY View on Reddit →

Source: Reddit r/appliancerepair