Fisher & Paykel Washing Machine: pump running continuously

Professional Repair Guide

What is this symptom?

Is your Fisher & Paykel washing machine's pump running continuously? This issue can prevent your machine from completing cycles and may be caused by a clogged drain pump filter, a faulty water level switch, or even a malfunctioning drain pump motor. Identifying the cause can help you address this frustrating problem effectively.

Urgency: Medium

Possible Causes

Clogged drain pump filter or drain hose

How to Identify: Pump runs continuously and water either drains slowly, not at all, or there is debris visible in pump filter area; hose kinks or blockages may be present.

Part: Drain pump filter / drain hose

Faulty water level (pressure) switch

How to Identify: Pump runs because machine incorrectly senses water level; cycles reset or ECU tries to drain despite low water.

Part: Water level sensor / pressure switch

Faulty drain pump motor stuck ON

How to Identify: Pump runs even when cycle is stopped and system thinks drain complete; replacing pump stops continuous run.

Part: Drain pump assembly

Next step

Choose the next step for pump running continuously

Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.

Based on diagnostic data

Most relevant component to inspect

Drain Pump

Pumps waste water out of the appliance during the drain cycle.

Typical part-only price
$35 - $80
DIY difficulty
Easy
Estimated time
15-30 mins
Where can I find the model number?

Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.

Find a part that fits my model

Verify the complete model and part number on the retailer's compatibility page before ordering.

Also check
RepairClinic

Other components that may be involved

Check these only if your diagnosis points to them.

Possible related component

Pressure Switch

Detects the water level inside the tub and signals when to start or stop filling.

$25 - $65 · Easy · 15-30 mins

Check fit & price

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.

Preventive Maintenance

  • Clean drain pump filter and inspect drain hose: Blockages that can lead to continuous pump operation
    Frequency: every 3 months
  • Run maintenance wash with no clothes: Debris build‑up in drum and drain system
    Frequency: monthly

Frequently Asked Questions

Why is my Fisher & Paykel Washing Machine pump running continuously?
The pump may be running continuously due to a clogged drain pump filter, a faulty water level switch, or a malfunctioning drain pump motor.
How do I fix Fisher & Paykel Washing Machine pump running continuously myself?
No DIY solutions are recommended for this issue. It’s advisable to contact a professional for proper diagnosis and repair.
How much does it cost to fix pump running continuously?
Repair costs can vary depending on the cause, but it's best to get a quote from a professional technician for an accurate estimate.
When should I call a technician for pump running continuously?
You should call a technician if the pump runs continuously despite troubleshooting, as this may indicate a more complex issue.

References & Sources

Community Analytical Insights

Analysis based on real user discussions from appliance repair communities

Can I Fix This Myself?

65%
DIY Success Rate Difficulty: Either

Common Issues Reported by Users

  • Faulty pressure switch causing continuous pump operation
  • Clogged drain hose or filter preventing proper drainage
  • Electrical issue or short circuit in the control board

User Suggested Solutions

  1. Inspect and replace the pressure switch if faulty. To do this, unplug the machine, locate the pressure switch (usually near the water tank), and test it with a multimeter. Replace if defective.

  2. Check and clean the drain hose and filter. Disconnect the hose from the machine and inspect for blockages. Clean the filter located at the bottom front of the machine.

  3. Inspect the control board for any visible signs of damage or burnt components. If damage is found, replace the control board. This may require professional assistance.

Analysis based on 1 community discussions
View Sources

Data compiled from real discussions on r/appliancerepair and r/Appliances:

  1. Fisher & Paykel smart drive excellence 6.5 Drain pump runs c...

Community Discussions

Drain pump runs continuously even when turned off

After leaving the machine alone for a week, it started working properly.

DIY View on Reddit →

Source: Reddit r/appliancerepair

User Comments (0)

Share your experience or solution below.

Be the first to comment!