Electrolux Washing Machine: excess water after wash
What is this symptom?
Is your Electrolux washing machine leaving excess water in the drum after the wash cycle? This common issue can result from a clogged drain pump filter, a kinked drain hose, or even a malfunctioning drain pump. Understanding the causes can help you effectively address the problem and restore your machine's functionality.
Important Tips for Electrolux Models
- Electrolux troubleshooting literature specifically highlights blocked drain and checking the hose connected to the sink trap as a key step for residual water after wash.
Possible Causes
Clogged drain pump filter or drain path
How to Identify: Water remains after cycle; check for visible debris when opening the filter access panel; slow or no drainage during wash.
Part: Drain pump filter / drainage path
Kinked or improperly positioned drain hose
How to Identify: Inspect the hose behind the washer; sharp bends or kinks can obstruct water flow leading to residual water.
Part: Drain hose
Drain pump malfunction
How to Identify: No humming from pump during drain, even with clear hoses and filter; persistent water remaining after wash cycles.
Part: Drain pump
Drainage system or household drain blockage (external)
How to Identify: Wear issues when draining into a sink; slow drainage; water backs up into washer drain.
Part: Household drain / sink trap
DIY Solutions
Clean drain pump filter
- Turn off and unplug the washing machine.
- Locate the access panel for the drain filter (usually at front bottom).
- Place bowl/towel to catch water and slowly open the filter to remove water.
- Remove debris and lint from the filter and rinse clean.
- Reinstall filter securely and test wash cycle to confirm drainage.
Straighten and check drain hose
- Unplug washer and pull it slightly away from wall.
- Inspect the drain hose for kinks, twists, or pinches.
- Straighten hose and ensure it is positioned at correct height per manual.
- Run a rinse cycle to see if water now drains.
Next step
Choose the next step for excess water after wash
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Drain Pump
Pumps waste water out of the appliance during the drain cycle.
- Typical part-only price
- $35 - $80
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Drain Hose
Carries waste water from the drain pump to your home's standpipe or sink drain.
Model-compatible Washing Machine parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Washing Machine Cleaner Tablets
Routine tub-cleaning supplies for residue and odor control. They do not repair a mechanical, drainage, or electronic fault.
Braided Washer Inlet Hoses
A maintenance replacement option for visibly worn external fill hoses. Verify thread size, length, and hot/cold connection requirements.
Washer Drain Hose Holder
Helps secure an external drain hose at the standpipe. It does not correct an internal pump or control fault.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Professional Repairs
Replace faulty drain pump
Clear deep external drain blockages
When to Call a Professional
Preventive Maintenance
-
Clean drain pump filter: Blockages that cause water to remain after wash
Frequency: every 1-2 months -
Inspect and straighten drain hose: Drain hose obstructions
Frequency: every 3-6 months
Frequently Asked Questions
Why is my Electrolux Washing Machine excess water after wash?
How do I fix Electrolux Washing Machine excess water after wash myself?
How much does it cost to fix excess water after wash?
When should I call a technician for excess water after wash?
References & Sources
Community Analytical Insights
Guidance from available sources; statistical claims are shown only for samples of at least 10 discussions
Common Issues Reported by Users
- Clogged drain filter or hose
- Faulty water level sensor
- Overloaded washing machine
User Suggested Solutions
-
Check and clean the drain filter and hose. Disconnect the washing machine from power, locate the drain filter (usually at the front bottom), remove it, and clean any debris. Also, inspect the drain hose for blockages.
-
Test the water level sensor. Access the sensor (usually located near the drum), and check for any visible damage or blockages. If faulty, replace the sensor.
-
Reduce the load size. Ensure you are not overloading the washing machine, as this can prevent proper spinning and draining. Follow the manufacturer's guidelines for load capacity.
Limited-source guidance; percentages and success-rate claims are not shown
View
Sources
Data compiled from real discussions on r/appliancerepair and r/Appliances:
Community Discussions
how do a spin only to get rid of extra water
Use the rinse and spin cycle while disabling the Pure Rinse option.
Source: Reddit r/appliancerepair
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!