Electrolux Dishwasher Error i30
⚡ Quick Answer: The Electrolux dishwasher i30 error indicates a water leakage issue, triggered by the internal leak detection system. This system activates when water... ✅ DIY Fixable
What Does Error i30 Mean?
The Electrolux dishwasher i30 error indicates a water leakage issue, triggered by the internal leak detection system. This system activates when water accumulates in the base of the appliance, suggesting a potential leak or overflow condition. Users may notice a flashing error display, continuous beeping, and the drain pump running constantly. It's crucial to address this issue promptly to prevent further damage.
Common Symptoms:
- Dishwasher displays i30 code (or equivalent three beeps/three flashes).
- Dishwasher drain pump runs continuously (constant hum).
- Water may be present under the dishwasher or leaking.
Possible Causes
- Internal leak detected by the anti‑flood system (high)
- Excessive foam causing overflow triggering anti‑flood protection (medium)
- Obstruction or misloading directing water spray into seals causing leakage into base (medium)
How to Fix Error i30
DIY Fix Initial user‑level checks and reset
- Turn off the dishwasher and close the water supply.
- Ensure the unit is level and correctly installed.
- Check the loading: remove large items that may block spray arms.
- Clean filters, spray arms, and sump area.
- Unplug the dishwasher or disconnect power for ~10–15 minutes to reset and allow water or foam to dissipate.
- Reconnect and restart to see if error returns.
Technician Only Service diagnostics and repair
- Remove base access covers and tilt dishwasher to inspect the bottom tray for water.
- Drain and dry any water collected in the base tray; locate source of leak.
- Check and replace failed seals, gaskets, hoses, or sump components if leakage is identified.
- Inspect the flood sensor/float switch for proper function and replace if defective.
- Inspect and test drain pump and related plumbing for blockages or mechanical failure.
Parts needed: Seals and gaskets, Hoses (inlet and drain), Drain pump, Anti‑flood float or sensor
- If water is observed leaking under the appliance.
- If the error returns after basic user troubleshooting.
- If internal components (pump, float, seals) show signs of failure.
Next step
Choose the next step for i30
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Drain Pump
Pumps waste water out of the appliance during the drain cycle.
- Typical part-only price
- $35 - $80
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Model-compatible Dishwasher parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Dishwasher Cleaner and Descaler
Supports routine removal of mineral scale, grease, and odor. It is maintenance, not a repair for a failed pump, valve, or control.
Braided Dishwasher Inlet Hose
For replacement of an externally damaged supply hose. Verify connection size, length, and appliance installation requirements before ordering.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Technical Specifications
| wattage | 1440W |
|---|---|
| component | Leak Sensor |
| resistance | 10-20 ohms |
| part_number | 154565001 |
| voltage_rating | 120V AC |
Common Questions
What does i30 error mean on Electrolux dishwasher?
The i30 error indicates a water leak detected by the dishwasher's anti-flood system, causing continuous beeping and a flashing display.
Can I fix Electrolux dishwasher i30 error myself?
Yes, perform initial checks by turning off the unit, closing the water supply, ensuring it's level, and removing any blockages.
How much does it cost to fix i30 error?
Repair costs vary; replacing parts like the pump or sensor can range from moderate to higher based on region and model.
When should I call a technician for i30?
Call a technician if you notice water leaking under the appliance, if the error persists after troubleshooting, or if internal components show signs of failure.
Sources & References
Data last verified: 2026-07-25
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!