Electrolux Dishwasher Error E2
⚡ Quick Answer: The Electrolux dishwasher error E2 indicates a malfunction in the heating circuit, often caused by a faulty heating element or temperature sensor. Use... ✅ DIY Fixable
What Does Error E2 Mean?
The Electrolux dishwasher error E2 indicates a malfunction in the heating circuit, often caused by a faulty heating element or temperature sensor. Users may notice the E2 code displayed on the control panel, along with improper water heating and incomplete wash cycles. To resolve this issue, basic troubleshooting steps such as checking door closure and resetting the appliance can be attempted before moving on to more involved repairs.
Common Symptoms:
- Dishwasher displays E2 on control panel
- Dishwasher may not heat water properly or complete cycle
Possible Causes
- Heating element malfunction (high)
- Temperature sensor/thermistor fault affecting heating (medium)
How to Fix Error E2
DIY Fix Check basic conditions & reset
- Ensure the dishwasher door is fully closed and latched
- Power appliance off at breaker or unplug for a few minutes, then restore power to clear transient errors
Technician Only Inspect and test heating circuit components
- Disconnect dishwasher from mains power
- Remove lower access panel to access heating element and temperature sensor
- Use a multimeter to test heating element for continuity and correct resistance
- Test temperature sensor (thermistor) per manufacturer specifications
- Inspect wiring harness for damage or loose connections
- Replace faulty heating element or sensor as needed
Parts needed: heating element, temperature sensor/thermistor, associated wiring harness
- If multimeter tests indicate component failure and you’re not trained to replace internal parts safely
- If error persists after basic resets and cleaning
Next step
Choose the next step for E2
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Heating Element
Heats the water or air inside the appliance to the required temperature.
- Typical part-only price
- $40 - $95
- DIY difficulty
- Medium
- Estimated time
- 30-45 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Temperature Sensor
Monitors the internal temperature to ensure correct operation and prevent overheating.
Thermistor
Measures precise temperature changes and sends resistance feedback to the control board.
Wiring Harness
Connects controls, sensors, motors, and other electrical components inside the appliance.
Model-compatible Dishwasher parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Dishwasher Cleaner and Descaler
Supports routine removal of mineral scale, grease, and odor. It is maintenance, not a repair for a failed pump, valve, or control.
Braided Dishwasher Inlet Hose
For replacement of an externally damaged supply hose. Verify connection size, length, and appliance installation requirements before ordering.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Technical Specifications
| wattage | 60W |
|---|---|
| component | Drain Pump |
| resistance | 10-30 ohms |
| part_number | 154568001 |
| voltage_rating | 120V AC |
Common Questions
What does E2 error mean on Electrolux dishwasher?
E2 indicates a malfunction in the heating circuit, often related to the heating element or temperature sensor.
Can I fix Electrolux dishwasher E2 error myself?
Yes, you can check if the door is closed properly and reset the appliance to clear transient errors.
How much does it cost to fix E2 error?
The estimated repair cost for the E2 error ranges from $50 to $200+, depending on the parts needed.
When should I call a technician for E2?
Call a technician if multimeter tests indicate component failure or if the error persists after basic troubleshooting.
Sources & References
Data last verified: 2026-07-25
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!