Candy Dryer Error E3
⚡ Quick Answer: The Candy dryer E3 error indicates that the water condensate tank is full or the float sensor is malfunctioning, preventing the dryer from completing ... ✅ DIY Fixable
What Does Error E3 Mean?
The Candy dryer E3 error indicates that the water condensate tank is full or the float sensor is malfunctioning, preventing the dryer from completing its cycle. If the tank is empty but the E3 code persists, the float switch may be stuck or faulty, or there could be a blockage affecting the drainage.
Common Symptoms:
- Dryer stops mid‑cycle and displays E3
- Water/condensate tank full indicator is shown while the tank may be full or not
- Cycle won’t resume until tank emptied and reset
Possible Causes
- Water/condensate tank genuinely full or not seated correctly (high)
- Float switch or sensor stuck, dirty, or faulty (medium)
- Pump or drainage blockage causing water not to reach tank properly (medium)
How to Fix Error E3
DIY Fix Empty and Check the Condensate Water Tank
- Turn off and unplug the dryer.
- Remove the water/condensate tank completely.
- Empty all water into a sink or drain.
- Rinse the tank if necessary and ensure no lint/fibers are obstructing it.
- Re‑insert the tank fully until it clicks.
- Plug in and restart a drying cycle to see if E3 clears.
DIY Fix Clean Float/Sensor Area
- After emptying the tank, inspect the float sensor area on the tank and in the dryer.
- Remove any lint or debris that might jam the float.
- Ensure float moves freely and isn’t stuck in the ‘full’ position.
- Reassemble and test if the error clears.
Technician Only Inspect and Service Pump/Sensor Circuit
- Disconnect power and access the condensate pump and float switch wiring.
- Test the float switch and water level sensor for correct operation with a multimeter.
- Check the pump and drainage channel for blockages or mechanical faults.
- Replace any faulty sensor, switch, or pump component.
- Verify wiring integrity between the sensor/pump and control board.
Parts needed: Float switch or water level sensor, Condensate pump, Associated wiring/connectors
- After emptying tank and cleaning sensor area if E3 persists
- If you’re uncomfortable accessing internal components such as sensors or pumps
- If water leaks or overflow persists despite tank maintenance
Next step
Choose the next step for E3
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Wiring Harness
Connects controls, sensors, motors, and other electrical components inside the appliance.
- Typical part-only price
- $20 - $120
- DIY difficulty
- Medium
- Estimated time
- 30-90 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Model-compatible Dryer parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Dryer Vent Cleaning Kit
Helps remove routine lint buildup from an accessible dryer vent path. It does not diagnose or repair an E-code or failed component.
Lint Trap Cleaning Brush
A narrow brush for routine cleaning around an accessible lint screen and housing.
Dryer Vent Hose Kit
A replacement exhaust duct option for visibly crushed or damaged external venting. Check diameter, length, local code, and installation clearance.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Technical Specifications
| wattage | 2400W |
|---|---|
| component | Heating Element |
| resistance | 10-30 ohms |
| part_number | CANDY 41026920 |
| voltage_rating | 230V AC |
Common Questions
What does E3 error mean on Candy dryer?
The E3 error means the condensate tank is full or the float sensor is malfunctioning.
Can I fix Candy dryer E3 error myself?
Yes, you can empty the tank and clean the float/sensor area to resolve the issue.
How much does it cost to fix E3 error?
Repair costs range from $50 to $200+, depending on parts and labor.
When should I call a technician for E3?
Call a technician if the E3 error persists after maintenance or if you're uncomfortable with DIY repairs.
Sources & References
- Error Code - E3 - Candy Condenser Dryer Support (community)
- Candy Dryer Error Codes List (incl. E3) (community)
- Significato codici di errore Candy Dryer (community)
Data last verified: 2026-07-25
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!