White-Westinghouse Oven Error F2
⚡ Quick Answer: The F2 error code on your White Westinghouse oven indicates an over-temperature condition, often caused by a malfunctioning temperature sensor or cont... ✅ DIY Fixable
What Does Error F2 Mean?
The F2 error code on your White Westinghouse oven indicates an over-temperature condition, often caused by a malfunctioning temperature sensor or control board. This error typically appears when the oven heats or attempts to heat, leading to erratic temperature readings and inconsistent cooking results. If the error persists, further investigation is needed to identify the faulty component.
Common Symptoms:
- F2 displayed when oven heats or attempts to heat
- Error appears during or shortly after heating cycle
- Oven may shut down/beep along with the code
Possible Causes
- Faulty oven temperature sensor (medium)
- Control board / Electronic Oven Control interpreting incorrect temperature data (medium)
How to Fix Error F2
DIY Fix Basic system reset
- Turn off power to the oven at the circuit breaker or unplug it
- Wait 1–2 minutes
- Restore power and observe if F2 returns
Technician Only Test and replace oven temperature sensor
- Disconnect power to oven at circuit breaker
- Access sensor (usually inside oven cavity rear)
- Test sensor resistance with a multimeter (expected ~1100 ohms at room temp)
- Replace sensor if readings are abnormal
Parts needed: oven temperature sensor
Technician Only Inspect and potentially replace control board
- Disconnect oven power
- Access control board area
- Inspect for burned components or faulty operation
- Replace control board if confirmed defective
Parts needed: control board (Electronic Oven Control)
- After basic checks (reset, sensor continuity) if the error persists
- If you are uncomfortable or inexperienced with electrical/mechanical oven repairs
- If visible damage to wiring or board is found
Next step
Choose the next step for F2
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Temperature Sensor
Monitors the internal temperature to ensure correct operation and prevent overheating.
- Typical part-only price
- $15 - $35
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Main Control Board
The central brain of the appliance that controls all components, cycles, and timings.
Model-compatible Oven parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Non-Scratch Cooktop Cleaner
A routine surface-care product. Confirm that it is approved for the specific glass, ceramic, enamel, or stainless finish.
Oven Thermometer
A diagnostic aid for comparing cavity temperature during a controlled check. It does not prove which internal component has failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Technical Specifications
| wattage | N/A |
|---|---|
| component | Temperature Sensor |
| resistance | 1000-1200 ohms |
| part_number | WB21X5301 |
| voltage_rating | 120V AC |
Common Questions
What does F2 error mean on white westinghouse oven?
F2 indicates an over-temperature condition, often due to a faulty temperature sensor or control board.
Can I fix white westinghouse oven F2 error myself?
Yes, try a basic system reset by turning off the power for 1-2 minutes.
How much does it cost to fix F2 error?
Repair costs range from $50 to $150 for parts, depending on the model.
When should I call a technician for F2?
Call a technician if the error persists after basic checks or if you find visible damage.
Data last verified: 2026-07-26
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!