Montpellier Dishwasher Error F2
⚡ Quick Answer: The Montpellier dishwasher F2 error indicates a malfunction related to water drainage. This issue may arise due to a blocked drainage system, excess s... ✅ DIY Fixable
What Does Error F2 Mean?
The Montpellier dishwasher F2 error indicates a malfunction related to water drainage. This issue may arise due to a blocked drainage system, excess suds affecting the water level sensor, or an obstruction in the float switch. Symptoms include the dishwasher stopping mid-cycle, standing water at the end of the cycle, or the error appearing during the drain phase. Addressing these issues promptly can prevent further complications.
Common Symptoms:
- Dishwasher stops mid‑cycle with F2 displayed
- Standing water in the dishwasher at end of cycle or when error appears
- Error appears shortly after start or during drain phase
Possible Causes
- Blocked or restricted drainage system (medium)
- Excess suds/foam interfering with water level sensing (medium)
- Float switch or water level sensor obstruction (medium)
How to Fix Error F2
DIY Fix Check and clear drainage components
- Turn off and unplug the dishwasher for safety.
- Remove any standing water with towels or a sponge.
- Access and remove the bottom filter; clean out food debris and residues.
- Inspect the drain hose under the sink for kinks, bends, or blockages and straighten/clear as needed.
- Run a short rinse cycle to see if draining has improved.
DIY Fix Check water level and float switch area
- Open the dishwasher and locate the float switch (usually near bottom of dishwasher tub).
- Ensure it moves freely; remove any debris or suds around it.
- If excess suds are present, run a rinse cycle without detergent to clear foam.
Technician Only Inspect drain pump and sensor components
- Disconnect power and remove access panels to reach the drain pump.
- Test the drain pump for electrical continuity and mechanical operation; replace if defective.
- Check for debris lodged in the pump impeller or housing and clear as necessary.
- Test the float switch or water level sensor with a multimeter for proper functionality.
Parts needed: Drain pump, Float switch / water level sensor
- If the F2 error persists after cleaning filters, clearing hoses, and checking the float switch.
- If you detect a suspected mechanical failure in the drain pump or sensors (no spin at drain phase, unusual noises).
Next step
Choose the next step for F2
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Drain Pump
Pumps waste water out of the appliance during the drain cycle.
- Typical part-only price
- $35 - $80
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Float Switch
Detects the maximum water level to prevent overflow and potential flooding.
Pressure Switch
Detects the water level inside the tub and signals when to start or stop filling.
Model-compatible Dishwasher parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Dishwasher Cleaner and Descaler
Supports routine removal of mineral scale, grease, and odor. It is maintenance, not a repair for a failed pump, valve, or control.
Braided Dishwasher Inlet Hose
For replacement of an externally damaged supply hose. Verify connection size, length, and appliance installation requirements before ordering.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Technical Specifications
| note | The previous model-independent part specification was removed. Verify the full model number and diagnosis in the manufacturer's official parts catalog before ordering. |
|---|---|
| part_number | None |
Common Questions
What does F2 error mean on montpellier dishwasher?
The F2 error signifies a drainage malfunction, often due to blockages or excess suds.
Can I fix montpellier dishwasher F2 error myself?
Yes, you can check and clear drainage components and the float switch area.
How much does it cost to fix F2 error?
Repair costs range from £50 to £180 for pump or sensor replacements, plus labor.
When should I call a technician for F2?
Call a technician if the F2 error persists after DIY fixes or if there's suspected mechanical failure.
Data last verified: 2026-07-31
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!