Maytag Dishwasher Error F9E1

⚡ Quick Answer: The Maytag Dishwasher error F9E1 signifies a drain pump failure, preventing the unit from completing its drain cycle. This issue is often marked by un... ✅ DIY Fixable

What Does Error F9E1 Mean?

The Maytag Dishwasher error F9E1 signifies a drain pump failure, preventing the unit from completing its drain cycle. This issue is often marked by unusual noises and standing water in the tub, typically caused by a clogged filter, an obstruction in the drain hose, or a malfunctioning drain pump. Addressing these problems promptly is essential to restore proper operation.

Common Symptoms:

  • Error code displayed toward end of wash cycle when draining should occur.
  • Standing water remains in dishwasher tub.
  • Dishwasher prevents completion of cycle due to inability to drain.

Possible Causes

  • Clogged dishwasher filter or drain path (medium)
  • Obstruction in drain hose (medium)
  • Kinked or incorrectly installed drain hose (medium)
  • Blockage in garbage disposal connection (knockout plug or obstruction) (medium)
  • Drain pump obstruction or failure (medium)

How to Fix Error F9E1

DIY Fix Check and clean drain filter and path

  1. Turn off and disconnect power to the dishwasher.
  2. Remove the bottom rack to access the filter at the tub bottom.
  3. Remove the filter assembly and rinse it under warm water to clear debris.
  4. Reinstall the filter and run a short rinse cycle to test.

DIY Fix Inspect drain hose for kinks or blockages

  1. Turn off power and water to the dishwasher.
  2. Pull the dishwasher out to access the drain hose.
  3. Inspect the hose for kinks and straighten them.
  4. If needed, disconnect the hose and flush it with water to clear clogs.
  5. Reconnect securely and test the dishwasher.

DIY Fix Verify garbage disposal connection

  1. Ensure the garbage disposer knockout plug has been removed if connected.
  2. Run the garbage disposal to clear any blockages that might back up into the dishwasher drain.
  3. Test the dishwasher for improved drainage.

Technician Only Inspect and service drain pump

  1. Disconnect all power to the dishwasher.
  2. Remove access panels and locate the drain pump.
  3. Check for debris or obstruction in the pump impeller and clear as needed.
  4. Test pump operation; replace if defective.

Parts needed: Drain pump assembly

DIY Fix Reset dishwasher control

  1. Turn off power at the circuit breaker or unplug the dishwasher.
  2. Wait at least 30–60 seconds.
  3. Restore power and run a test cycle.
🛑 When to Call a Pro:
  • If the error persists after clearing debris and resetting.
  • If the drain pump hums but does not drain water.
  • If you detect leaks, cracked hoses, or damaged pump components.

Next step

Choose the next step for F9E1

Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.

Based on diagnostic data

Most relevant component to inspect

Drain Pump

Pumps waste water out of the appliance during the drain cycle.

Typical part-only price
$35 - $80
DIY difficulty
Easy
Estimated time
15-30 mins
Where can I find the model number?

Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.

Find a part that fits my model

Verify the complete model and part number on the retailer's compatibility page before ordering.

Also check
RepairClinic

Other parts options

Check related components first; use model search as a fallback.

Model number required

Model-compatible Dishwasher parts

Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.

Find a part that fits my model

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.

Optional routine care

Maintenance supplies

These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.

Maintenance supply

Dishwasher Cleaner and Descaler

Supports routine removal of mineral scale, grease, and odor. It is maintenance, not a repair for a failed pump, valve, or control.

View maintenance supply
Maintenance supply

Braided Dishwasher Inlet Hose

For replacement of an externally damaged supply hose. Verify connection size, length, and appliance installation requirements before ordering.

View maintenance supply

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.

Technical Specifications

wattage 50W
component Drain Pump
resistance 10-30 ohms
part_number W10827151
voltage_rating 120V AC

Common Questions

What does F9E1 error mean on Maytag Dishwasher?

F9E1 indicates a drain pump failure, causing the dishwasher to not drain and often resulting in standing water.

Can I fix Maytag Dishwasher F9E1 error myself?

Yes, you can clean the drain filter, inspect the drain hose, and reset the dishwasher to troubleshoot the issue.

How much does it cost to fix F9E1 error?

The estimated repair cost for the F9E1 error ranges from $80 to $200, including parts and labor.

When should I call a technician for F9E1?

Call a technician if the error persists after cleaning, if the drain pump hums without draining, or if you notice leaks.

Sources & References

Data last verified: 2026-07-22

User Comments (0)

Share your experience or solution below.

Be the first to comment!