Kleenmaid Dishwasher Error E10
⚡ Quick Answer: The Kleenmaid dishwasher E10 error code signals a potential issue with the drain pump, commonly associated with a humming noise and an inability to dr... ✅ DIY Fixable
What Does Error E10 Mean?
The Kleenmaid dishwasher E10 error code signals a potential issue with the drain pump, commonly associated with a humming noise and an inability to drain water effectively. This may arise from blockages in the inlet or drain hoses or issues with the water supply. To resolve this, check that the water supply is connected and turned on, ensure the dishwasher door is securely closed, and consult the user manual for specific troubleshooting steps.
Possible Causes
- Drain pump blockage
- Faulty drain pump
- Clogged drain hose
How to Fix Error E10
DIY Fix Check basic dishwasher systems
- Consult the official user manual for your specific Kleenmaid model and verify if there is an entry for the E10 error code.
- Inspect that water supply is connected and turned on, the dishwasher door is fully closed, and no obvious blockages exist in inlet or drain hoses.
- Try resetting the dishwasher by turning it off, waiting a few minutes, and restarting the cycle.
Technician Only Conduct professional diagnostics
- Access the dishwasher control panel and use a service monitor/test mode if available for your Kleenmaid model to read exact fault registers.
- Inspect inlet valve, water level sensors, communication between control board modules, and heating/drying components relevant to E10 conditions.
- Use a multimeter to test continuity of suspected components and replace parts only after confirming failure.
Parts needed: Inlet valve, Sensors (water level, temperature), Control board modules
- If the error persists after basic checks and resetting.
- If you are uncertain about safe electrical or water connections.
Next step
Choose the next step for E10
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Main Control Board
The central brain of the appliance that controls all components, cycles, and timings.
- Typical part-only price
- $120 - $280
- DIY difficulty
- Medium
- Estimated time
- 20-40 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Model-compatible Dishwasher parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Dishwasher Cleaner and Descaler
Supports routine removal of mineral scale, grease, and odor. It is maintenance, not a repair for a failed pump, valve, or control.
Braided Dishwasher Inlet Hose
For replacement of an externally damaged supply hose. Verify connection size, length, and appliance installation requirements before ordering.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Technical Specifications
| note | The previous model-independent part specification was removed. Verify the full model number and diagnosis in the manufacturer's official parts catalog before ordering. |
|---|---|
| part_number | None |
Common Questions
What does E10 error mean on Kleenmaid dishwasher?
The E10 error indicates a problem with the drain pump, often causing humming and failure to drain.
Can I fix Kleenmaid dishwasher E10 error myself?
Yes, check the water supply, ensure the door is closed, and reset the dishwasher.
How much does it cost to fix E10 error?
Repair costs can vary widely depending on the component that fails.
When should I call a technician for E10?
Call a technician if the error persists after basic checks or if you're unsure about electrical or water connections.
Sources & References
Data last verified: 2026-07-31
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!