JennAir Oven Error F2
⚡ Quick Answer: The JennAir oven error F2 indicates an over-temperature condition, where the control system detects temperatures exceeding the normal operating range,... ✅ DIY Fixable
What Does Error F2 Mean?
The JennAir oven error F2 indicates an over-temperature condition, where the control system detects temperatures exceeding the normal operating range, typically above 600°F. This can lead to erratic temperature readings and inconsistent cooking results. Symptoms include the F2 error displayed on the panel, potential oven shutoff, and issues with temperature regulation.
Common Symptoms:
- Error F2 displayed on oven panel
- Oven may shut off due to over‑temperature
- Potential continuous heating or failure to regulate temperature
Possible Causes
- Oven temperature exceeding safe threshold as sensed by control (high)
- Faulty oven temperature sensor or its wiring (high)
- Stuck relay or malfunction on control/power relay board causing overheating (medium)
How to Fix Error F2
DIY Fix Reset power and monitor
- Turn off oven and disconnect power at circuit breaker for at least 1 minute.
- Restore power and observe if F2 recurs during normal use.
DIY Fix Check for obvious temperature issues
- Allow oven to cool fully.
- Avoid using high temperature modes until issue is resolved.
- Use an external oven thermometer to check if actual temperature matches set temperature (optional).
Technician Only Test and replace oven temperature sensor
- Disconnect oven from power.
- Locate temperature sensor at back of oven interior.
- Test sensor resistance with multimeter and compare with manufacturer spec.
- Replace sensor if readings are out of specification.
Parts needed: oven temperature sensor
Technician Only Inspect and repair wiring and control board/relays
- Disconnect power and access control/power relay board.
- Inspect for stuck relays, burn marks, or damaged wiring between sensor and control.
- Repair or replace control board or power relay board as needed.
Parts needed: control board, power relay board, wiring harness
- Error persists after resetting and basic checks
- Heating elements remain energized when off
- Uncertainty about safely testing internal components
Next step
Choose the next step for F2
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Temperature Sensor
Monitors the internal temperature to ensure correct operation and prevent overheating.
- Typical part-only price
- $15 - $35
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Main Control Board
The central brain of the appliance that controls all components, cycles, and timings.
Wiring Harness
Connects controls, sensors, motors, and other electrical components inside the appliance.
Model-compatible Oven parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Non-Scratch Cooktop Cleaner
A routine surface-care product. Confirm that it is approved for the specific glass, ceramic, enamel, or stainless finish.
Oven Thermometer
A diagnostic aid for comparing cavity temperature during a controlled check. It does not prove which internal component has failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Technical Specifications
| note | The previous model-independent part specification was removed. Verify the full model number and diagnosis in the manufacturer's official parts catalog before ordering. |
|---|---|
| part_number | None |
Common Questions
What does F2 error mean on jennair oven?
F2 error indicates an over-temperature condition, often resulting in erratic cooking results.
Can I fix jennair oven F2 error myself?
Yes, you can reset the power and monitor for recurrence or check for temperature issues.
How much does it cost to fix F2 error?
Estimated repair costs range from $30 to $150 for sensor replacement.
When should I call a technician for F2?
Call if the error persists after resetting or if heating elements remain on when off.
Sources & References
- F2 - Error Code - Range - JennAir Product Help (official)
- Jenn‑Air Oven / Range Error Code F2 explanation (community)
Data last verified: 2026-07-31
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!