JennAir Oven Error F1-3
⚡ Quick Answer: The JennAir Oven F1-3 error code signifies a malfunction in the temperature sensing circuit, which may involve the temperature sensor, wiring, or cont... ⚠️ Difficulty Varies
What Does Error F1-3 Mean?
The JennAir Oven F1-3 error code signifies a malfunction in the temperature sensing circuit, which may involve the temperature sensor, wiring, or control board. This error can lead to inaccurate temperature readings, the oven not heating properly, or the oven refusing to start baking or broiling. It's crucial to address this issue promptly to ensure safe and effective operation of your oven.
Common Symptoms:
- Oven displays F1‑3 error code on the control panel
- Oven may refuse to start bake/broil or shut off due to sensed temperature fault (community reports)
Possible Causes
- Faulty Oven Temperature Sensor or Sensor Circuit (Open/Disconnected) (medium)
- Loose or Damaged Temperature Sensor Wiring / Harness (medium)
- Control Board or Related Control Component Issue (less common) (low)
How to Fix Error F1-3
DIY Fix Power Cycle the Oven
- Turn off power at the circuit breaker for at least 1 minute.
- Turn the power back on and monitor if the error returns.
Technician Only Diagnose and Repair Temperature Sensor Circuit
- Disconnect oven power at the breaker.
- Access the oven cavity and locate the temperature sensor (thin metal probe on oven back wall).
- Disconnect sensor and test resistance with a multimeter; compare to expected OEM nominal resistance (often ~1050 ohms at room temperature per independent repair guides).
- Inspect and repair/replace any broken wiring or harness between the sensor and control board.
- Replace the temperature sensor if open or out of spec.
- Reassemble and power up to confirm resolution.
Parts needed: Oven Temperature Sensor, Wiring Harness (if damaged), Multimeter (for testing)
- If the oven still displays F1‑3 after basic reset and visible wiring checks.
- If you are not comfortable accessing internal oven components.
Next step
Choose the next step for F1-3
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Temperature Sensor
Monitors the internal temperature to ensure correct operation and prevent overheating.
- Typical part-only price
- $15 - $35
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Wiring Harness
Connects controls, sensors, motors, and other electrical components inside the appliance.
Model-compatible Oven parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Non-Scratch Cooktop Cleaner
A routine surface-care product. Confirm that it is approved for the specific glass, ceramic, enamel, or stainless finish.
Oven Thermometer
A diagnostic aid for comparing cavity temperature during a controlled check. It does not prove which internal component has failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Technical Specifications
| note | The previous model-independent part specification was removed. Verify the full model number and diagnosis in the manufacturer's official parts catalog before ordering. |
|---|---|
| part_number | None |
Common Questions
What does F1-3 error mean on JennAir Oven?
F1-3 indicates a malfunction in the temperature sensing circuit, leading to heating issues.
Can I fix JennAir Oven F1-3 error myself?
Yes, you can power cycle the oven to reset it, but check wiring for visible issues.
How much does it cost to fix F1-3 error?
Repair costs typically range from $50 to $150 for parts, plus technician labor.
When should I call a technician for F1-3?
Call a technician if the error persists after a reset or if you're uncomfortable with repairs.
Sources & References
- F1‑3 Error Code — JennAir Product Help (official)
Data last verified: 2026-07-31
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!