Haier Dishwasher Error E20
⚡ Quick Answer: The Haier dishwasher error E20 indicates a drainage malfunction, primarily due to a clogged drain filter or a faulty drain pump. This error typically ... ✅ DIY Fixable
What Does Error E20 Mean?
The Haier dishwasher error E20 indicates a drainage malfunction, primarily due to a clogged drain filter or a faulty drain pump. This error typically results in water not draining at the end of the cycle, leading to standing water in the dishwasher base and unusual noises during operation. To resolve this issue, it is essential to check and clear the drain filter and hoses. If the problem persists, a technician may need to inspect or replace the drain pump.
Common Symptoms:
- Water not draining at end of cycle
- Error appears during or after wash cycle
- Standing water in dishwasher base
Possible Causes
- Clogged drain filter or debris in drain system (medium)
- Faulty drain pump (medium)
How to Fix Error E20
DIY Fix Check and clear drain filter and hoses
- Turn off and unplug your dishwasher.
- Open the dishwasher and locate the bottom drain filter.
- Remove and clean the drain filter of food debris and residue.
- Inspect the drain hose under the sink for kinks or blockages; straighten or clear as needed.
- Run a short cycle to see if the error clears.
Technician Only Inspect/replace drain pump
- Disconnect power and water supply.
- Access the dishwasher’s lower panel to reach the drain pump.
- Test the pump for proper operation and continuity.
- Replace the drain pump if faulty, ensuring proper reconnection of hose and electrical connections.
- Test operation after reassembly.
Parts needed: Drain pump assembly, Drain hose/clamps
- If cleaning the filter/hose does not resolve the error and the unit still fails to drain
- If unusual noises continue when attempting to drain
- If internal components (pump/motor) test faulty
Next step
Choose the next step for E20
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Drain Pump
Pumps waste water out of the appliance during the drain cycle.
- Typical part-only price
- $35 - $80
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other components that may be involved
Check these only if your diagnosis points to them.
Drain Hose
Carries waste water from the drain pump to your home's standpipe or sink drain.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Technical Specifications
| wattage | 50W |
|---|---|
| component | Drain Pump |
| resistance | 10-30 ohms |
| part_number | Haier 006061 |
| voltage_rating | 120V AC |
Common Questions
What does E20 error mean on haier dishwasher?
E20 error indicates a drainage malfunction, often due to a clogged drain filter or a faulty drain pump.
Can I fix haier dishwasher E20 error myself?
Yes, you can check and clean the drain filter and hoses to potentially resolve the E20 error.
How much does it cost to fix E20 error?
The estimated repair cost for the E20 error ranges from $50 to $200, depending on parts and labor.
When should I call a technician for E20?
Call a technician if cleaning the filter does not resolve the error, or if there are unusual noises during draining.
Data last verified: 2026-07-25
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!