Haier Dishwasher Error E2
⚡ Quick Answer: The Haier dishwasher error E2 indicates a drainage malfunction, where the appliance fails to drain water properly. This may cause water to remain in t... ✅ DIY Fixable
What Does Error E2 Mean?
The Haier dishwasher error E2 indicates a drainage malfunction, where the appliance fails to drain water properly. This may cause water to remain in the tub after a cycle or halt operation mid-cycle. The most common cause is a clogged or blocked drain hose, but the issue may also stem from an obstructed drain pump or filter, or a faulty drain pump. Addressing these issues promptly can restore your dishwasher's functionality.
Common Symptoms:
- Water remains in the tub after or during cycle
- Dishwasher stops mid‑cycle when trying to drain
Possible Causes
- Clogged or blocked drain hose (high)
- Obstructed drain pump or filter (medium)
- Faulty drain pump (medium)
How to Fix Error E2
DIY Fix Check and clear drainage components
- Turn off and unplug the dishwasher.
- Remove and inspect the drain hose for kinks, bends, or blockages; straighten or clear as needed.
- Open the dishwasher, remove the lower rack, and clean the filter and sump area of any debris.
- Reconnect and test by running a short drain cycle to see if the error clears.
Technician Only Inspect and service drain pump and internal drainage system
- Disconnect power to the dishwasher and remove access panels.
- Test the drain pump motor for operation and continuity; replace if defective.
- Inspect the drain hose routing and check valve for wear or obstruction.
- Reassemble and verify proper draining in multiple cycles.
Parts needed: Drain pump, Drain hose, Filter assembly, Check valve
- If after clearing visible blockages the E2 code persists.
- If drain pump fails to operate or makes unusual noise.
- If there are signs of leaks, electrical faults, or other error codes concurrently.
Next step
Choose the next step for E2
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Drain Pump
Pumps waste water out of the appliance during the drain cycle.
- Typical part-only price
- $35 - $80
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other components that may be involved
Check these only if your diagnosis points to them.
Drain Hose
Carries waste water from the drain pump to your home's standpipe or sink drain.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Technical Specifications
| wattage | 50W |
|---|---|
| component | Drain Pump |
| resistance | 10-20 ohms |
| part_number | Haier 006193 |
| voltage_rating | 120V AC |
Common Questions
What does E2 error mean on haier dishwasher?
The E2 error indicates a drainage malfunction, causing water to remain in the tub or the dishwasher to stop mid-cycle.
Can I fix haier dishwasher E2 error myself?
Yes, you can check and clear the drain hose and filter for blockages to potentially resolve the issue.
How much does it cost to fix E2 error?
The estimated repair cost for the E2 error ranges from $80 to $250, depending on parts and labor.
When should I call a technician for E2?
Call a technician if the E2 code persists after clearing blockages, if the drain pump is noisy, or if there are signs of leaks.
Sources & References
- Haier Dishwasher Support – E2 Drainage Issue (official)
Data last verified: 2026-07-25
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!