Maytag Dishwasher: stopping during final drain cycle

Professional Repair Guide

What is this symptom?

Is your Maytag dishwasher stopping during the final drain cycle? This common issue can leave water standing in the tub and prevent the cycle from completing. Possible causes include a clogged drain path, a faulty drain pump, or incorrect drain hose installation. Understanding these issues can help you troubleshoot effectively and restore your dishwasher's performance.

Urgency: Medium

Important Tips for Maytag Models

Maytagâ€™s own drain troubleshooting suggests checking air gap and disposer connection for blockages which can prevent proper draining.

Possible Causes

Clogged drain path (filter, drain hose, air gap) preventing proper drainage

How to Identify: Water remains after wash; long drain times; visible debris in filter; kinks in hose

Part: Drain hose, air gap, filters

Faulty drain pump or pump motor assembly

How to Identify: Unusual noises (humming during drain attempt; pump not running; no water flow during drain

Part: Drain pump and motor assembly

Incorrect drain hose installation (improper height or loops)

How to Identify: Drain hose loop too low/high causing backflow; water remains due to siphoning issues

Part: Drain hose

Control board error or control/sensor miscommunication

How to Identify: Error codes on display; intermittent stopping at different phases; unrelated visible blockages absent

Part: Control board / sensors

DIY Solutions

Clean filters and clear debris in drain path

Easy 10-20 minutes

Tools Needed: screwdriver (if needed), flashlight

Turn off power to dishwasher
Remove and clean filter assembly of debris
Check drain hose for kinks or visible clogs and straighten
Clean air gap (if present) of debris

⚠️ Safety First: Ensure power is off before reaching into components

Inspect and clear drain hose

Moderate 15-30 minutes

Tools Needed: bucket, long brush or flexible cleaning tool

Disconnect dishwasher power
Place bucket under hose connection
Disconnect drain hose from sink/disposer and dishwasher
Run water or brush through hose to clear debris
Reattach hose and restore power

⚠️ Safety First: Be careful of water spills; ensure proper hose reattachment

Professional Repairs

Replace drain pump/motor assembly

Estimated Cost: $200 - $450

Control board/sensor diagnostics and replacement

Estimated Cost: $200 - $600+

When to Call a Professional

Persistent water left after cleaning drain path and pump checks

Strange noises from pump or motor suggesting mechanical failure

Error codes on control panel indicating electrical faults

Door not latching properly triggering cycle stops

Preventive Maintenance

Clean dishwasher filters: Drain clogs and incomplete drain cycles
Frequency: monthly
Inspect drain hose for kinks: Drain blockages and water remaining at end of cycle
Frequency: every 3 months

Frequently Asked Questions

Why is my Maytag Dishwasher stopping during final drain cycle?

Common causes include a clogged drain path, a faulty drain pump, or incorrect drain hose installation.

How do I fix Maytag Dishwasher stopping during final drain cycle myself?

Clean filters, clear debris in the drain path, and inspect the drain hose for clogs.

How much does it cost to fix stopping during final drain cycle?

Professional repairs for this issue can range from $200 to $600+, depending on the problem.

When should I call a technician for stopping during final drain cycle?

If DIY solutions don't resolve the issue or if you suspect a faulty pump or control board.

Community Analytical Insights

Analysis based on real user discussions from appliance repair communities

Can I Fix This Myself?

70%

DIY Success Rate Difficulty: Either

Common Issues Reported by Users

Loose or faulty door latch causing interruption in the cycle
Clogged drain hose or filter preventing proper drainage
Malfunctioning drain pump that fails to remove water

User Suggested Solutions

Inspect and reseat the door latch. Open and close the dishwasher door firmly to ensure the latch engages properly. If the latch is damaged, consider replacing it.
Check and clean the drain hose and filter. Disconnect the hose and inspect for clogs. Clean the filter located at the bottom of the dishwasher to ensure proper drainage.
Test the drain pump for functionality. If the pump is not working, replace it. This may involve removing the dishwasher from its installation for access.

Analysis based on 1 community discussions
View Sources

Data compiled from real discussions on r/appliancerepair and r/Appliances:

Dishwasher stopping on final drain cycle

Community Discussions

Dishwasher stops on final drain cycle

The door latch may be loose due to cabinet expansion, causing the cycle to interrupt. Reseating the latch by opening and closing the door allows the cycle to continue.