Maytag Dishwasher: not completing wash cycle

Professional Repair Guide

What is this symptom?

Is your Maytag dishwasher starting a wash cycle but not completing it? This issue may cause the cycle to pause mid-way or require you to press Start/Resume repeatedly. Common causes include a faulty door latch, water inlet valve issues, or control panel malfunctions. Troubleshooting can help identify the problem before seeking professional repair.

Urgency: Medium

Important Tips for Maytag Models

Maytag official guidance notes door open/unaltered Start/Resume indicator flashing means the cycle has paused due to door or power interruption; pressing Start/Resume and ensuring door is latched may resume normal cycle. (Product Help | Maytag)0search0
Maytag documentation suggests resetting the dishwasher control by disconnecting power for 30+ seconds can clear control errors that interrupt cycles. (Product Help | Maytag)1search2

Possible Causes

Door latch or door switch failure

How to Identify: Dishwasher stops mid-cycle or pauses; door may not fully latch; cycle resumes when door is re‑closed; safety mechanism may interpret door as open.

Part: Door latch assembly / door switch

Water inlet valve malfunction or water supply issue

How to Identify: Dishwasher stops after draining and fails to fill; insufficient water detected; no new water enters the tub.

Part: Water inlet valve

Control panel / touchpad or main control board failure

How to Identify: Buttons unresponsive, display errors, dishwasher stops without error codes, control interface glitches.

Part: Control panel, touchpad, or main control board

Power interruption or control reset needed

How to Identify: Cycle stops when power blips or breaker trips; may resume after reset; Start/Resume indicator flashing.

Part: Control system/power supply

DIY Solutions

Reset dishwasher control panel

Easy 5–10 minutes

Turn off dishwasher power at plug or household circuit breaker.
Wait at least 1 minute for control to reset.
Restore power and close door firmly.
Select cycle and press Start to resume.
Observe if cycle completes normally.

⚠️ Safety First: Ensure power is turned off at breaker before disconnecting power.

Inspect and clean door latch area

Moderate 10–20 minutes

Tools Needed: Screwdriver, clean cloth

Open dishwasher door fully.
Inspect latch for debris or damage preventing proper engagement.
Clean latch area with cloth.
Close door firmly and check if it latches securely; attempt new cycle.
Replace latch if it fails to engage properly (requires part from manufacturer).

⚠️ Safety First: Disconnect power before disassembling door trim.

Next step

Choose the next step for not completing wash cycle

Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.

Check during diagnosis

Most relevant component to inspect

Door or Lid Switch

Detects whether the appliance door or lid is safely closed before operation.

Typical part-only price: $15 - $55
DIY difficulty: Medium
Estimated time: 20-45 mins

Optional: enter your model number

Where can I find the model number?

Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.

Find a part that fits my model

Verify the complete model and part number on the retailer's compatibility page before ordering.

Other parts options

Check related components first; use model search as a fallback.

Possible related component

Water Inlet Valve

Controls the flow of hot and cold water into the appliance.

$25 - $60 · Easy · 15-30 mins

Check fit & price

Possible related component

Main Control Board

The central brain of the appliance that controls all components, cycles, and timings.

$120 - $280 · Medium · 20-40 mins

Check fit & price

Model number required

Model-compatible Dishwasher parts

Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.

Find a part that fits my model

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.

Optional routine care

Maintenance supplies

These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.

Maintenance supply

Dishwasher Cleaner and Descaler

Supports routine removal of mineral scale, grease, and odor. It is maintenance, not a repair for a failed pump, valve, or control.

View maintenance supply

Maintenance supply

Braided Dishwasher Inlet Hose

For replacement of an externally damaged supply hose. Verify connection size, length, and appliance installation requirements before ordering.

View maintenance supply

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.

Professional Repairs

Replace defective water inlet valve

Estimated Cost: $50–$150 for part plus labor

Replace control panel or control board

Estimated Cost: $100–$350 or higher depending on part

Replace door latch assembly

Estimated Cost: $50–$150 for parts plus labor

When to Call a Professional

Dishwasher stops mid-cycle repeatedly despite resets and basic cleaning

Fault codes display and DIY resets don’t resolve the issue

Internal components like control board or water valve need testing or replacement

Preventive Maintenance

Clean filter regularly: Clogs that might cause mid-cycle pauses
Frequency: monthly
Check and clean door latch area: Door switch false open detection causing cycle stops
Frequency: every 3–6 months

Frequently Asked Questions

Why is my Maytag Dishwasher not completing wash cycle?

Common causes include a faulty door latch, water inlet valve issues, or control panel failures.

How do I fix Maytag Dishwasher not completing wash cycle myself?

Try resetting the control panel or inspecting the door latch for debris.

How much does it cost to fix not completing wash cycle?

Repair costs can range from $50–$350 depending on the issue and parts needed.

When should I call a technician for not completing wash cycle?

Call a technician if DIY fixes do not resolve the issue or if complex repairs are needed.

References & Sources

Stops Mid Cycle - Dishwasher - Maytag Product Help Official

Community Analytical Insights

Guidance from available sources; statistical claims are shown only for samples of at least 10 discussions

Common Issues Reported by Users

Clogged or dirty filter preventing proper water flow
Faulty door latch causing the cycle to interrupt
Malfunctioning control board affecting cycle progression

User Suggested Solutions

Clean or replace the dishwasher filter. Step 1: Remove the bottom rack. Step 2: Locate the filter (usually near the spray arm). Step 3: Rinse it under hot water to remove debris. Step 4: Reinstall the filter and test the dishwasher.
Inspect and replace the door latch if faulty. Step 1: Open the door and check the latch for damage. Step 2: If damaged, purchase a replacement latch. Step 3: Remove the old latch and install the new one following the manufacturer's instructions.
Test and replace the control board if necessary. Step 1: Unplug the dishwasher and access the control board. Step 2: Inspect for visible damage or burnt components. Step 3: If damaged, replace the control board with a new one.

Limited-source guidance; percentages and success-rate claims are not shown
View Sources