Kenmore Dishwasher: grinding or buzzing noise

Professional Repair Guide

What is this symptom?

Are you hearing a persistent grinding or buzzing noise from your Kenmore dishwasher during wash or drain cycles? This unusual sound often indicates potential mechanical issues or foreign object obstructions. Addressing these noises promptly can prevent further damage and ensure optimal performance.

Urgency: Medium

Important Tips for Kenmore Models

  • Kenmore models commonly have replaceable wash impellers and pump/motor assemblies; noise often traced to debris in impeller housing.

Possible Causes

Foreign object obstruction in pump/chopper area

How to Identify: Grinding or buzzing that changes or stops when large debris is removed from sump; visible object in filter area

Part: Pump impeller / chopper blade

Damaged or worn wash/circulation pump impeller

How to Identify: Noise persists after removing debris; impeller fins cracked or rubbing housing on inspection

Part: Wash impeller in circulation pump

Failing motor bearings (circulation or drain pump)

How to Identify: Grinding/buzzing present even with no debris and consistent across cycles; older unit noise increasing over time

Part: Pump motor bearings

Spray arm or wash arm misalignment or damage

How to Identify: Noise more prominent during water spray; arms wobble or hit dishes, visible obstruction or damage on inspection

Part: Spray arm / wash arm assembly

Faulty water inlet valve causing buzzing

How to Identify: Buzzing primarily during fill stage, not continuous grinding; irregular water flow sounds

Part: Water inlet valve

DIY Solutions

Remove Debris from Filter/Sump and Inspect Pump Area

Moderate 15-30 minutes
Tools Needed: screwdriver, flashlight, gloves
  1. Turn off power to dishwasher.
  2. Open dishwasher, remove lower rack, and take out filter.
  3. Inspect sump for debris and remove any foreign objects.
  4. Check if the pump impeller area is clear of lodged particles.
  5. Reassemble and run a short cycle to test noise.
⚠️ Safety First: Disconnect power before reaching into sump

Inspect and Replace Spray Arms or Wash Arm Components

Moderate 30-60 minutes
Tools Needed: screwdriver, replacement spray arms if needed
  1. Turn off power and water supply.
  2. Remove spray arms per model instructions.
  3. Inspect for cracks, wear, or obstruction.
  4. Replace damaged spray arms or ensure they rotate freely.
  5. Reassemble and test cycle.
⚠️ Safety First: Ensure correct part matching for model

Next step

Choose the next step for grinding or buzzing noise

Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.

Other parts options

Check related components first; use model search as a fallback.

Possible related component

Drain Pump

Pumps waste water out of the appliance during the drain cycle.

$35 - $80 · Easy · 15-30 mins

Check fit & price
Possible related component

Spray Arm

Rotates and sprays high-pressure water to clean dishes inside the tub.

$20 - $55 · Easy · 5-10 mins

Check fit & price
Possible related component

Water Inlet Valve

Controls the flow of hot and cold water into the appliance.

$25 - $60 · Easy · 15-30 mins

Check fit & price
Model number required

Model-compatible Dishwasher parts

Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.

Find a part that fits my model

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.

Optional routine care

Maintenance supplies

These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.

Maintenance supply

Dishwasher Cleaner and Descaler

Supports routine removal of mineral scale, grease, and odor. It is maintenance, not a repair for a failed pump, valve, or control.

View maintenance supply
Maintenance supply

Braided Dishwasher Inlet Hose

For replacement of an externally damaged supply hose. Verify connection size, length, and appliance installation requirements before ordering.

View maintenance supply

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.

Professional Repairs

Replace Pump Impeller or Entire Pump Assembly

Estimated Cost: $80 - $250

Replace Circulation/Drain Pump Motor

Estimated Cost: $150 - $400

Replace Water Inlet Valve

Estimated Cost: $50 - $150

When to Call a Professional

Grinding/buzzing persists after debris removal and basic checks
Visible damage to pump impeller or motor components
Water not circulating or draining properly alongside noise
Leaks or electrical issues present

Preventive Maintenance

  • Regularly clean filter and sump area: Debris buildup causing grinding noises and pump strain
    Frequency: monthly
  • Inspect spray arms and rotating parts: Misalignment or damage that can contribute to noise
    Frequency: quarterly

Frequently Asked Questions

Why is my Kenmore Dishwasher grinding or buzzing noise?
Common causes include foreign object obstructions, damaged pump impellers, and failing motor bearings.
How do I fix Kenmore Dishwasher grinding or buzzing noise myself?
Turn off the power, remove the lower rack, and inspect the filter and sump for debris.
How much does it cost to fix grinding or buzzing noise?
Professional repairs can range from $80 to $400 depending on the issue.
When should I call a technician for grinding or buzzing noise?
If DIY solutions don't resolve the issue, or if the noise persists, it's best to consult a professional.

Community Analytical Insights

Guidance from available sources; statistical claims are shown only for samples of at least 10 discussions

Common Issues Reported by Users

  • Foreign object in the impeller or spray arm
  • Worn or damaged motor bearings
  • Faulty or obstructed drain pump

User Suggested Solutions

  1. Remove the lower spray arm and check for any debris or foreign objects in the impeller. Clean thoroughly and reassemble.

  2. Inspect the motor bearings for wear. If they are damaged, consider replacing the motor assembly.

  3. Check the drain pump for blockages. Remove any debris and ensure the pump is functioning properly.

Limited-source guidance; percentages and success-rate claims are not shown
View Sources

Data compiled from real discussions on r/appliancerepair and r/Appliances:

  1. Kenmore Dishwasher Model #66517033402 | Grinding / Buzzing N...

User Comments (0)

Share your experience or solution below.

Be the first to comment!