Indesit Washing Machine: not spinning properly
What is this symptom?
Is your Indesit washing machine not spinning properly? You may notice that the drum fails to spin at all, leaves clothes wet, or struggles to complete the spin cycle. This issue can stem from unbalanced loads, clogged filters, or worn belts. Don't let laundry pile up—let's explore the solutions!
Important Tips for Indesit Models
- Error codes like F08 may indicate spin or drainage issues specific to some models
- Door lock failure is a commonly reported brand-specific cause that prevents spin cycle
Possible Causes
Unbalanced load or overloading
How to Identify: Drum stops spinning with heavy or uneven items, machine shakes or vibrates, spin cycle cancels automatically.
Part: Drum & load sensors
Clogged drain pump/filter or drain hose
How to Identify: Water remains in drum, slow or no drainage before/when spinning, wet clothes post cycle.
Part: Drain pump, filter, drain hose
Drive belt worn, loose, or broken
How to Identify: Drum won’t spin at all, belt visible wear or break on inspection, loose feel on manual rotation.
Part: Drive belt
Faulty door lock or lid switch
How to Identify: Machine won’t start or spin cycle when door/ lid not recognized as closed.
Part: Door lock/lid switch assembly
Faulty motor or motor components (e.g., brushes, capacitor)
How to Identify: Humming but no spin, burning smell, or intermittent spinning.
Part: Motor assembly
Control board or electronic module failure
How to Identify: No pattern to failure, unresponsive controls, no spin despite other systems OK.
Part: Control board/electronics
DIY Solutions
Redistribute or reduce load
- Open door and remove some items to avoid overloading
- Evenly distribute remaining clothes around the drum
- Restart the spin cycle to test
Clean drain pump filter and hose
- Unplug machine and place bucket to catch water
- Locate and open access panel to drain filter
- Remove debris in filter and flush with water
- Inspect and clear drain hose if possible
- Reassemble and test spin cycle
Inspect drive belt
- Unplug machine and pull it away from wall
- Remove back panel to access belt
- Check belt for wear, breakage or slipping
- Replace belt if needed (note exact part required)
- Reassemble and test
Next step
Choose the next step for not spinning properly
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Drain Hose
Carries waste water from the drain pump to your home's standpipe or sink drain.
- Typical part-only price
- $15 - $30
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Drain Pump
Pumps waste water out of the appliance during the drain cycle.
Drive Belt
Transfers rotational power from the motor to turn the drum or tub.
Capacitor
Stores electrical energy to assist in starting or running the motor efficiently.
Model-compatible Washing Machine parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Washing Machine Cleaner Tablets
Routine tub-cleaning supplies for residue and odor control. They do not repair a mechanical, drainage, or electronic fault.
Braided Washer Inlet Hoses
A maintenance replacement option for visibly worn external fill hoses. Verify thread size, length, and hot/cold connection requirements.
Washer Drain Hose Holder
Helps secure an external drain hose at the standpipe. It does not correct an internal pump or control fault.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Professional Repairs
Replace motor or motor components
Replace control board or electronic module
When to Call a Professional
Preventive Maintenance
-
Clean drain filter and hose: Clogs that stop spin cycle
Frequency: monthly -
Avoid overloading: Imbalance and excessive stress
Frequency: Every load
Frequently Asked Questions
Why is my Indesit Washing Machine not spinning properly?
How do I fix Indesit Washing Machine not spinning properly myself?
How much does it cost to fix not spinning properly?
When should I call a technician for not spinning properly?
References & Sources
Community Analytical Insights
Guidance from available sources; statistical claims are shown only for samples of at least 10 discussions
Common Issues Reported by Users
- Shipping bolts are still installed, preventing proper drum movement.
- Unbalanced load causing the machine to stop spinning to prevent damage.
- Worn out or damaged drive belt affecting drum rotation.
User Suggested Solutions
-
Remove shipping bolts and ensure the drum can spin freely. Check the user manual for proper removal instructions.
-
Redistribute the load by rearranging clothes in the drum to ensure balance. Run a spin cycle to test.
-
Inspect the drive belt for wear or damage. If damaged, replace the drive belt following the manufacturer's instructions.
Limited-source guidance; percentages and success-rate claims are not shown
View
Sources
Data compiled from real discussions on r/appliancerepair and r/Appliances:
Community Discussions
ran with shipping bolts, went on a walk during spin mode
Remove shipping bolts and test the machine again.
Source: Reddit r/appliancerepair
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!