Frigidaire Washing Machine: not draining completely
What is this symptom?
Is your Frigidaire washing machine not draining completely? If your washer finishes the cycle but leaves water in the drum, your clothes might end up soggy. This common issue can stem from a clogged drain hose or pump, making it essential to identify the cause for effective solutions.
Important Tips for Frigidaire Models
- Frigidaire washers may require correct standpipe height and not fully sealed drain hose in install; improper install can affect draining.
Possible Causes
Clogged or kinked drain hose
How to Identify: Water drains slowly or not at all; visible kinks in hose; debris seen or felt when disconnecting hose.
Part: Drain hose
Clogged drain pump or debris in pump/filter area
How to Identify: Water remains after cycle; unusual noises from pump area; debris (coins, lint found in pump filter when accessed.
Part: Drain pump / pump filter
Faulty drain pump
How to Identify: No noise from pump during drain cycle; pump runs but fails to move water; audible humming without flow.
Part: Drain pump
Lid switch/door latch malfunction (top-load or front-load safety interlock)
How to Identify: Washer does not initiate drain cycle; no click when lid closed; continuity test fails on switch.
Part: Lid switch / door latch
Faulty control board or timer not powering pump
How to Identify: No voltage to drain pump during drain cycle; visible board damage; other electrical anomalies.
Part: Control board / Timer
DIY Solutions
Check and straighten the drain hose
- Unplug the washer and pull it away from wall.
- Inspect drain hose for kinks or sharp bends.
- Disconnect hose and check inside for debris.
- Straighten hose and reattach securely.
- Run a short drain cycle to test.
Clean drain pump filter and remove debris
- Unplug washer.
- Access front/bottom panel to locate pump/filter.
- Place towels/bucket to catch water.
- Remove debris from filter and pump housing.
- Reassemble and test drain cycle.
Test lid switch/door latch continuity
- Unplug washer.
- Access lid switch/door latch area.
- Use multimeter to test for continuity when lid closed.
- Replace switch if no continuity detected.
- Reassemble and test.
Next step
Choose the next step for not draining completely
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Drain Hose
Carries waste water from the drain pump to your home's standpipe or sink drain.
- Typical part-only price
- $15 - $30
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Drain Pump
Pumps waste water out of the appliance during the drain cycle.
Door Latch Assembly
Mechanically secures the appliance door and may operate a door-closed safety switch.
Door or Lid Switch
Detects whether the appliance door or lid is safely closed before operation.
Model-compatible Washing Machine parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Washing Machine Cleaner Tablets
Routine tub-cleaning supplies for residue and odor control. They do not repair a mechanical, drainage, or electronic fault.
Braided Washer Inlet Hoses
A maintenance replacement option for visibly worn external fill hoses. Verify thread size, length, and hot/cold connection requirements.
Washer Drain Hose Holder
Helps secure an external drain hose at the standpipe. It does not correct an internal pump or control fault.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Professional Repairs
Replace drain pump
Replace control board/timer
Replace lid switch or door latch assembly
When to Call a Professional
Preventive Maintenance
-
Inspect and clean drain hose and pump filter: Clogs and incomplete drainage
Frequency: every 3-6 months -
Avoid overloading and remove small items from pockets: Foreign objects entering drain system
Frequency: Each use
Frequently Asked Questions
Why is my Frigidaire Washing Machine not draining completely?
How do I fix Frigidaire Washing Machine not draining completely myself?
How much does it cost to fix not draining completely?
When should I call a technician for not draining completely?
References & Sources
Community Analytical Insights
Guidance from available sources; statistical claims are shown only for samples of at least 10 discussions
Common Issues Reported by Users
- Clogged drain filter or pump
- Improperly positioned drain hose
- Faulty drain pump
User Suggested Solutions
-
Check and clean the drain filter. Locate the filter, usually at the front bottom of the washer, remove it, and clean any debris. Also, check the drain pump for blockages.
-
Inspect the drain hose for kinks or improper positioning. Ensure it is elevated and not submerged in water. Adjust as necessary.
-
Test the drain pump for functionality. If it is not working, you may need to replace it. Disconnect power, remove the pump, and install a new one if necessary.
Limited-source guidance; percentages and success-rate claims are not shown
View
Sources
Data compiled from real discussions on r/appliancerepair and r/Appliances:
Community Discussions
not completely draining
Check for clogs and ensure the drain hose is properly positioned.
Source: Reddit r/appliancerepair
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!