Frigidaire Washing Machine: loud during spin cycles
What is this symptom?
Are you experiencing excessive noise from your Frigidaire washing machine during the spin cycle? Loud sounds such as banging, grinding, or roaring can indicate issues like an unbalanced load, worn drum bearings, or damaged suspension components. Understanding these symptoms is crucial for effective troubleshooting.
Important Tips for Frigidaire Models
- Frigidaire official guidance states unbalanced loads and improperly removed shipping bolts can cause loud noises; tub bearing and seal defects are d as key causes of excessive noise during spin.
Possible Causes
Unbalanced load or uneven laundry distribution
How to Identify: Loud banging or thumping that changes when stopping and redistributing clothes; machine shakes violently with heavy items on one side.
Part: Drum/load distribution
Worn or defective tub/drum bearings or tub seal failure
How to Identify: Persistent rumbling or grinding that increases with speed; rough or gritty feel when manually rotating drum; possible leaks near transmission.
Part: Drum bearings/tub seal
Damaged or worn shock absorbers or suspension components
How to Identify: Banging, loud knocking noise with excessive drum movement; machine vibrates excessively or "walks."
Part: Shock absorbers/suspension springs
DIY Solutions
Redistribute laundry to balance load
- Pause or stop the washer mid‑cycle.
- Open drum and evenly distribute clothes around the tub.
- Avoid washing one heavy item alone; mix large and small items.
- Restart wash cycle and observe noise reduction.
Level the washer on the floor
- Ensure washer is off and unplugged.
- Use a level on top of the washer to check alignment.
- Adjust the leveling feet by turning until washer is stable and balanced.
- Tighten lock nuts on leveling feet.
- Run a spin cycle to test noise.
Remove foreign objects from drum and pump
- Unplug washer.
- Inspect drum and around seals for trapped items.
- Check pump filter (if accessible) for coins/debris.
- Remove objects found and reassemble.
- Run a test spin to check noise reduction.
Next step
Choose the next step for loud during spin cycles
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Drum Bearing Kit
Supports the spinning drum and ensures smooth, quiet rotation during cycles.
- Typical part-only price
- $40 - $95
- DIY difficulty
- Hard
- Estimated time
- 120-180 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Washer Shock Absorber
Dampens tub movement and vibration during high-speed spin cycles.
Model-compatible Washing Machine parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Washing Machine Cleaner Tablets
Routine tub-cleaning supplies for residue and odor control. They do not repair a mechanical, drainage, or electronic fault.
Braided Washer Inlet Hoses
A maintenance replacement option for visibly worn external fill hoses. Verify thread size, length, and hot/cold connection requirements.
Washer Drain Hose Holder
Helps secure an external drain hose at the standpipe. It does not correct an internal pump or control fault.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Professional Repairs
Replace drum bearings and tub seal
Replace shock absorbers or suspension components
Inspect/replace drive pulley or belt
When to Call a Professional
Preventive Maintenance
-
Regularly check and redistribute laundry to avoid imbalanced loads: Loud noise and vibration during spin cycle
Frequency: each use -
Inspect drum and remove foreign objects: Rattling and clanking noises from trapped debris
Frequency: monthly -
Ensure washer is level: Excessive vibration and noise
Frequency: periodically
Frequently Asked Questions
Why is my Frigidaire Washing Machine loud during spin cycles?
How do I fix Frigidaire Washing Machine loud during spin cycles myself?
How much does it cost to fix loud during spin cycles?
When should I call a technician for loud during spin cycles?
References & Sources
Community Analytical Insights
Guidance from available sources; statistical claims are shown only for samples of at least 10 discussions
Common Issues Reported by Users
- Worn or damaged drum bearings
- Loose or damaged counterweights
- Unbalanced load during spin cycle
- Faulty drive belt or motor coupling
User Suggested Solutions
-
Inspect and replace worn drum bearings. To do this, unplug the machine, remove the outer casing, and check the bearings for wear. If damaged, replace them with new ones. Reassemble and test the machine.
-
Check and secure counterweights. Open the machine's casing, locate the counterweights, and ensure they are properly secured. If they are cracked or broken, replace them. Reassemble and test the machine.
-
Redistribute the load. If the machine is making loud noises, pause the cycle and check if the load is unbalanced. Adjust the load evenly and restart the spin cycle.
-
Inspect the drive belt or motor coupling for wear. Unplug the machine, remove the back panel, and check these components. Replace if necessary. Reassemble and test the machine.
Limited-source guidance; percentages and success-rate claims are not shown
View
Sources
Data compiled from real discussions on r/appliancerepair and r/Appliances:
Community Discussions
Washing machine started getting really loud during spin cycles
Counterweights can be replaced, but there was additional damage, leading to the decision to buy a new machine.
Source: Reddit r/appliancerepair
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!