Asko Washing Machine: not draining
What is this symptom?
Is your Asko washing machine not draining? If water is stuck in the drum, it may indicate a clogged drain pump filter, blocked drain hose, or a faulty pump motor. Addressing these issues promptly can prevent further damage and ensure your appliance runs smoothly.
Important Tips for Asko Models
- Error code E03 may indicate drain pump timeout or blockage.
- Some older models use water pump belts; inspect if applicable.
Possible Causes
Clogged drain pump filter or impeller
How to Identify: Water remains in drum; debris visible in clean-out filter; pump blocked by lint, coins or foreign objects.
Part: Drain pump/filter
Blocked or kinked drain hose
How to Identify: Hose bent, crushed, or full of debris; water cannot exit machine even after pump runs; hose obstruction test shows no flow.
Part: Drain hose
Faulty drain pump motor
How to Identify: Pump makes unusual noise or does not run; multimeter shows no continuity; all hoses clear but no drainage.
Part: Drain pump motor
Control board or timer not powering pump
How to Identify: Pump not receiving voltage during drain cycle (tested with multimeter, no error code for blockage.
Part: Control board/timer
Door/lid switch not registering
How to Identify: Front or top door not securely detected closed, inhibiting cycle progression into drain stage.
Part: Door/lid switch
DIY Solutions
Clean drain pump filter and remove debris
- Turn off power and unplug washer.
- Locate and open the clean-out access panel (usually at front bottom).
- Place towel/bucket under panel, loosen filter cap to drain water.
- Remove debris from filter and pump; manually clear impeller obstructions.
- Replace filter cap securely and restore panel; test drain cycle.
Check and clear drain hose obstruction
- Unplug the washer and pull it away from wall.
- Disconnect drain hose at both ends.
- Inspect hose for kinks or debris; run water through hose to confirm flow.
- Use brush or snake to clear blockage.
- Reinstall hose ensuring no sharp bends; test machine by running a drain/spin cycle.
Reset the machine electronics
- Turn off the washer and unplug it.
- Wait ~5 minutes to allow internal capacitors to discharge.
- Plug washer back in and run a rinse/drain cycle to see if issue persists.
Next step
Choose the next step for not draining
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Drain Pump
Pumps waste water out of the appliance during the drain cycle.
- Typical part-only price
- $35 - $80
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Drain Hose
Carries waste water from the drain pump to your home's standpipe or sink drain.
Main Control Board
The central brain of the appliance that controls all components, cycles, and timings.
Door or Lid Switch
Detects whether the appliance door or lid is safely closed before operation.
Model-compatible Washing Machine parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Washing Machine Cleaner Tablets
Routine tub-cleaning supplies for residue and odor control. They do not repair a mechanical, drainage, or electronic fault.
Braided Washer Inlet Hoses
A maintenance replacement option for visibly worn external fill hoses. Verify thread size, length, and hot/cold connection requirements.
Washer Drain Hose Holder
Helps secure an external drain hose at the standpipe. It does not correct an internal pump or control fault.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Professional Repairs
Replace drain pump motor
Control board or timer replacement
Replace door/lid switch assembly
When to Call a Professional
Preventive Maintenance
-
Clean drain filter: Debris blockages in drain system
Frequency: monthly -
Inspect drain hose and path: Hose kinks or buildup that impede drainage
Frequency: every 3 months
Frequently Asked Questions
Why is my Asko Washing Machine not draining?
How do I fix Asko Washing Machine not draining myself?
How much does it cost to fix not draining?
When should I call a technician for not draining?
Community Analytical Insights
Guidance from available sources; statistical claims are shown only for samples of at least 10 discussions
Common Issues Reported by Users
- Faulty pump (2 mentions)
- Control board issue (1 mentions)
User Suggested Solutions
-
Check and replace the pump
-
Inspect control board for faults
Limited-source guidance; percentages and success-rate claims are not shown
View
Sources
Data compiled from real discussions on r/appliancerepair and r/Appliances:
Community Discussions
Washing machine fills with water when not in use
Video link provided for troubleshooting
Source: Reddit r/appliancerepair
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!