Asko Washing Machine: motor fault

Professional Repair Guide

What is this symptom?

Experiencing a motor fault with your Asko washing machine? Common symptoms include error codes like E06/E12, failure to spin or agitate, unusual noises, or sudden stops during cycles. These issues often stem from motor drive faults, overloads, or worn components, and can disrupt your laundry routine significantly.

Urgency: High

Important Tips for Asko Models

Asko washing machines report specific motor faults using fault codes like E06 (Motor Drive Fault) and E12 (Motor Overload/Overheat), useful for precise diagnosis.

Possible Causes

Motor drive fault / motor control malfunction

How to Identify: Asko washer displays error codes E06, E12, or similar motor/motor drive related codes on the control panel; machine refuses to spin or agitate during cycles.

Part: Motor drive / inverter board / motor control electronics

Motor overload / overheated motor protection triggered

How to Identify: Washer stops mid-cycle or shuts off the motor with high load or heat; may display related fault codes; burning odor or heat from cabinet.

Part: Motor overload protector / thermal cut-out

Worn motor carbon brushes (for brushed motors)

How to Identify: Drum fails to start although machine receives power; sparking under the machine or intermittent run; noises during operation.

Part: Carbon brushes inside motor

Electrical wiring or connection fault

How to Identify: Intermittent motor function or failure to start; visible damage or loose connector on inspection.

Part: Motor wiring harness, connectors

DIY Solutions

Check and interpret motor-related error codes

Easy 5â€“15 minutes

Tools Needed: User manual

Refer to your modelâ€™s user manual or online source to decode displayed error codes (e.g., E06, E12 for motor/motor drive faults).
Note the specific motor-related fault reported, as codes often indicate the root subsystem (drive fault, overload, etc.).
Record the fault code and proceed with targeted troubleshooting based on the identified subsystem.

⚠️ Safety First: Do not attempt internal repairs with the machine plugged in.

Inspect basic wiring and connections to motor assembly

Moderate 15â€“30 minutes

Tools Needed: Screwdriver set, flashlight

Unplug the washing machine and access the rear or bottom panel to reach motor wiring.
Visually inspect connectors for obvious damage, loose clips, or corrosion.
Re-seat connectors and tighten any loose harness attachments before reassembling and testing.

⚠️ Safety First: Ensure machine is unplugged before opening panels.

Professional Repairs

Replace motor drive / inverter board

Estimated Cost: $150â€“$450

Replace motor and/or motor components (brushes or entire unit)

Estimated Cost: $120â€“$400

When to Call a Professional

Error codes indicating motor drive or electrical faults persist after basic checks

Burning smell or overheating detected from motor area

Motor replacement or motor electronics repair is required

Preventive Maintenance

Balance loads and avoid overloading: Motor overload and unnecessary strain
Frequency: Per use
Regularly check for debris and obstructions: Motor strain due to blockage
Frequency: Monthly

Frequently Asked Questions

Why is my Asko Washing Machine motor fault?

Common causes include motor drive faults, overloads, worn brushes, or electrical wiring issues.

How do I fix Asko Washing Machine motor fault myself?

Check error codes and inspect wiring connections; refer to the user manual for guidance.

How much does it cost to fix motor fault?

Professional repairs range from $120 to $450 depending on the issue and parts needed.

When should I call a technician for motor fault?

If DIY troubleshooting fails or if the problem appears complex, contact a technician immediately.

Community Analytical Insights

Analysis based on real user discussions from appliance repair communities

Can I Fix This Myself?

60%

DIY Success Rate Difficulty: Either

Common Issues Reported by Users

Faulty motor control board
Worn out motor bearings
Electrical issues (bad wiring or connections)

User Suggested Solutions

Inspect and replace the motor control board. Disconnect power, remove the back panel, locate the motor control board, and replace it with a new one.
Check and lubricate or replace motor bearings. Access the motor by removing the drum, inspect the bearings for wear, and replace if necessary.
Examine electrical connections for damage. Ensure the washing machine is unplugged, check all wiring to the motor and control board for frays or loose connections, and repair as needed.