Amana Washing Machine: not stopping draining

Professional Repair Guide

What is this symptom?

If your Amana washing machine is not stopping draining, it may continue to pump water even after the cycle is complete. This issue can also occur during washing, leading to continuous water removal or siphoning during filling. Understanding the potential causes can help you troubleshoot effectively.

Urgency: Medium

Important Tips for Amana Models

  • Amana guidance on drain hose height and using U‑shape form shows that incorrect hose positioning leads to siphoning issues.
  • Repair discussions note control board/timer defects specific to Amana models can cause continuous drain.

Possible Causes

Improper Drain Hose Installation Causing Siphoning

How to Identify: Water continuously exits due to gravity siphoning; hose inserted too deep into standpipe or too low height.

Part: Drain hose/standpipe configuration

Faulty or Shorted Control Board/Timer

How to Identify: Drain function runs without cycle command and never shuts off; inspection may reveal burnt components.

Part: Control board/washer timer

Pressure Switch (Water Level Sensor) Fault

How to Identify: Machine may misread water levels, causing improper drain behavior; video repairs show replacing sensor stops continuous drain.

Part: Pressure switch/pressure transducer

DIY Solutions

Adjust Drain Hose Position to Prevent Siphoning

Easy 10-20 minutes
Tools Needed: measuring tape, screwdriver or hose clamp tool
  1. Ensure drain hose end is at correct height per Amana specs.
  2. Reposition hose so it is not inserted too far into drain/standpipe and create a proper high loop.
  3. Secure hose with clip so it maintains position.
  4. Run a short cycle to verify continuous drain has stopped.
⚠️ Safety First: Turn off washer power before adjusting hose.

Inspect and Clean Drain Pump Filter / Hose

Moderate 20-40 minutes
Tools Needed: towels, bucket, screwdriver, gloves
  1. Unplug washer and place towels/bucket to catch water.
  2. Access the pump filter (front lower panel) and remove it.
  3. Clean out debris, lint, or objects caught in filter.
  4. Also inspect tub-to-pump hose for blockages and clear.
  5. Reassemble and test operation.
⚠️ Safety First: Unplug unit before working.

Professional Repairs

Control Board or Timer Replacement

Estimated Cost: $150 - $400

Pressure Switch / Transducer Replacement

Estimated Cost: $40 - $120

When to Call a Professional

Circuit board/timer fault suspected
Pressure switch/transducer testing indicates failure
Continuous drain persists after repositioning drain hose and clearing blockages

Preventive Maintenance

  • Check and reposition drain hose: Siphoning continuous drain issues
    Frequency: annually
  • Clean drain hoses and pump filter: Blockages that can contribute to improper draining
    Frequency: every 6 months

Frequently Asked Questions

Why is my Amana Washing Machine not stopping draining?
Common causes include improper drain hose installation, a faulty control board, or issues with the pressure switch.
How do I fix Amana Washing Machine not stopping draining myself?
You can adjust the drain hose position to prevent siphoning and clean the drain pump filter.
How much does it cost to fix not stopping draining?
Professional repairs can range from $40 to $400, depending on whether you need a pressure switch or control board replacement.
When should I call a technician for not stopping draining?
Consider calling a technician if DIY solutions do not work or if you're uncomfortable with electrical components.

References & Sources

Community Analytical Insights

Analysis based on real user discussions from appliance repair communities

Can I Fix This Myself?

65%
DIY Success Rate Difficulty: Either

Common Issues Reported by Users

  • Faulty drain pump causing continuous draining
  • Malfunctioning pressure switch not detecting water level
  • Control board failure leading to incorrect signals

User Suggested Solutions

  1. Inspect and replace the drain pump if necessary. Disconnect the power, remove the access panel, and test the pump for blockages or damage. Replace if faulty.

  2. Check the pressure switch for proper operation. Locate the pressure switch, inspect the hose for clogs, and test the switch with a multimeter. Replace if defective.

  3. Examine the control board for burnt components or loose connections. If damaged, replace the control board. Ensure all connections are secure before reassembling.

Analysis based on 1 community discussions
View Sources

Data compiled from real discussions on r/appliancerepair and r/Appliances:

  1. Amana Washing Machine Won't Stop Draining, Even After Replac...

Community Discussions

Washing machine won't stop draining, emits rubber-burning smell

Replace the control board or check the drain pump and pressure sensor.

Pro needed View on Reddit →

Source: Reddit r/appliancerepair

User Comments (0)

Share your experience or solution below.

Be the first to comment!