Amana Washing Machine: not rinsing

Professional Repair Guide

What is this symptom?

Is your Amana washing machine not rinsing properly? You may notice that clothes feel soapy, water remains in the drum, or the rinse cycle fails to start. This common issue can stem from drainage problems, overloading, excess detergent, or even a faulty water inlet valve. Understanding these causes can help you troubleshoot effectively.

Urgency: Medium

Important Tips for Amana Models

  • Amana official support does not list specific rinse cycle troubleshooting besides general balance and drainage hints.

Possible Causes

Drainage issues (clogged hose, pump, filter)

How to Identify: Water remaining in drum after wash, slow or no drainage, abnormal noises from pump area.

Part: Drain hose / drain pump / filter

Overloading of drum preventing proper rinse

How to Identify: Rinsing improves when smaller loads are used; laundry packed tightly in drum.

Part: User load practice

Excess detergent or wrong detergent causing suds & residue

How to Identify: Soap residue on clothes despite rinse, heavy suds visible.

Part: Detergent system / wash chemistry

Faulty water inlet valve (insufficient water for rinse)

How to Identify: Rinse cycle lacks adequate water filling; error codes or no water during rinse.

Part: Water inlet valve

Control board/timer malfunction causing cycle sequencing errors

How to Identify: Incorrect progression through wash/rinse cycles, inconsistent behavior not explained by mechanical issues.

Part: Control board / timer

DIY Solutions

Clean drain hose and filter

Moderate 30–60 minutes
Tools Needed: screwdriver, bucket, gloves
  1. Unplug washer and locate drain filter access panel.
  2. Place a bucket under filter, open and remove debris.
  3. Inspect drain hose for kinks or blockages, clear any obstruction.
⚠️ Safety First: Always unplug before accessing internal components

Reduce load size and redistribute clothes

Easy 5 minutes
  1. Remove excess items so load is about ¾ full or less.
  2. Evenly distribute clothes around the drum.
  3. Restart the rinse cycle.

Adjust detergent type and amount

Easy 5 minutes
  1. Use detergent appropriate for your washer type (HE if required).
  2. Measure and reduce detergent quantity per load size.
  3. Run an extra rinse cycle to clear residue.

Professional Repairs

Replace drain pump

Estimated Cost: $50–$150

Replace water inlet valve

Estimated Cost: $40–$120

Service control board/timer

Estimated Cost: $100–$300

When to Call a Professional

Persistent water remains after drain cleaning
Electrical or control board issues suspected
Pump humming but not pumping

Preventive Maintenance

  • Clean drain filter and hose: Clogs that impede rinse and drainage
    Frequency: every 3–6 months
  • Use correct detergent type and measure: Excessive suds and residue build-up
    Frequency: every wash

Frequently Asked Questions

Why is my Amana Washing Machine not rinsing?
Common causes include drainage issues, overloading, excess detergent, or a faulty water inlet valve.
How do I fix Amana Washing Machine not rinsing myself?
Try cleaning the drain hose, reducing the load size, and adjusting the detergent amount.
How much does it cost to fix not rinsing?
Professional repairs can range from $40 to $300, depending on the issue.
When should I call a technician for not rinsing?
If DIY solutions don't work or if you suspect a malfunctioning control board, it's time to call a professional.

References & Sources

Community Analytical Insights

Analysis based on real user discussions from appliance repair communities

Can I Fix This Myself?

75%
DIY Success Rate Difficulty: Either

Common Issues Reported by Users

  • Clogged drain filter or hose
  • Faulty mode shifter
  • Defective water level switch

User Suggested Solutions

  1. Check and clean the drain filter and hose. Ensure there are no obstructions preventing water from draining properly. Disconnect the power, locate the filter, and remove any debris.

  2. Inspect and replace the mode shifter (part number W10913953) if it is malfunctioning. This involves removing the back panel of the washer, disconnecting the old part, and installing the new one.

  3. Test the water level switch for proper operation. If it is stuck or defective, replace it. This may require accessing the control panel to reach the switch.

Analysis based on 1 community discussions
View Sources

Data compiled from real discussions on r/appliancerepair and r/Appliances:

  1. Amana Washer stops in rinse cycle

Community Discussions

stopped during the rinse cycle with water still in the basket

Replace the mode shifter (part number W10913953)

DIY View on Reddit →

Source: Reddit r/appliancerepair

User Comments (0)

Share your experience or solution below.

Be the first to comment!