Amana Washing Machine: not filling
What is this symptom?
Is your Amana washing machine not filling with water? This common issue can leave you frustrated as the drum remains dry despite selecting a wash cycle. Often, this problem can arise from simple causes like turned-off water supply valves, kinked hoses, or a faulty water inlet valve. Understanding these issues can help you troubleshoot effectively and get your washer back in action.
Important Tips for Amana Models
- Official Amana support emphasizes that both hot and cold water connections must be present for proper operation, even for cold wash cycles, due to water valve design.
Possible Causes
Water supply valves off or inadequate water supply
How to Identify: Both hot and cold water supply valves behind the washer are not fully open or there is low household water pressure. Check by running water from hoses directly into a bucket to confirm flow. (Product Help | Amana
Part: Household water supply valves / hoses
Kinked, blocked, or damaged inlet hoses
How to Identify: Visible bends, kinks, or low water flow when the hose is detached and tested. Inspect hose condition and connection at washer and supply.
Part: Water inlet hoses
Faulty water inlet valve
How to Identify: No water flows with adequate supply and unobstructed hoses; multimeter shows no continuity or valve does not actuate on power. (Product Help | Amana
Part: Water inlet valve assembly
Faulty lid switch or door lock (safety interlock)
How to Identify: Washer does not detect lid closed; cycle won't engage fill; test continuity on lid switch.(ä¿®ç†è¯Šæ‰€
Part: Lid switch / door latch assembly
Defective pressure switch or water level sensor
How to Identify: Washer incorrectly thinks tub is full or prematurely stops inlet; multimeter test of switch continuity.turn0(Product Help | Amana
Part: Pressure switch / water level sensor
Control board / timer signal failure
How to Identify: No electrical signal sent to inlet valve during fill; visible damage on board or test with multimeter. (ä¿®ç†è¯Šæ‰€
Part: Electronic control board / timer
DIY Solutions
Ensure water supply is on and hoses are unobstructed
- Turn off washing machine power.
- Check that both hot and cold water supply valves behind washer are fully open.
- Inspect hoses for visible kinks or damage; straighten or replace if needed.
- Disconnect hoses, hold ends over bucket, and turn on supply to verify water flow.
- Reconnect hoses tightly and secure.
Clean inlet valve screens
- Turn off water supply and power.
- Disconnect inlet hoses from machine.
- Inspect inlet valve mesh screens for debris.
- Gently clean screens with soft brush under water.
- Reconnect hoses and restore water and power.
Test and replace lid switch
- Unplug washer and open access panel.
- Locate lid switch and disconnect wires.
- Test switch continuity with multimeter.
- Replace switch if faulty following part-specific guide.
- Reassemble and test washer.
Next step
Choose the next step for not filling
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Water Inlet Valve
Controls the flow of hot and cold water into the appliance.
- Typical part-only price
- $25 - $60
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Door Latch Assembly
Mechanically secures the appliance door and may operate a door-closed safety switch.
Pressure Switch
Detects the water level inside the tub and signals when to start or stop filling.
Main Control Board
The central brain of the appliance that controls all components, cycles, and timings.
Model-compatible Washing Machine parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Washing Machine Cleaner Tablets
Routine tub-cleaning supplies for residue and odor control. They do not repair a mechanical, drainage, or electronic fault.
Braided Washer Inlet Hoses
A maintenance replacement option for visibly worn external fill hoses. Verify thread size, length, and hot/cold connection requirements.
Washer Drain Hose Holder
Helps secure an external drain hose at the standpipe. It does not correct an internal pump or control fault.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Professional Repairs
Replace water inlet valve
Replace pressure switch / water level sensor
Control board / timer replacement
When to Call a Professional
Preventive Maintenance
-
Inspect and replace inlet hoses: Kinked or deteriorated hoses causing low or no water fill
Frequency: Every 2–5 years -
Clean inlet screens: Sediment buildup restricting water flow
Frequency: Annually
Frequently Asked Questions
Why is my Amana Washing Machine not filling?
How do I fix Amana Washing Machine not filling myself?
How much does it cost to fix not filling?
When should I call a technician for not filling?
References & Sources
Community Analytical Insights
Guidance from available sources; statistical claims are shown only for samples of at least 10 discussions
Common Issues Reported by Users
- Faulty pressure transducer (1 mentions)
- Faulty water level sensor (1 mentions)
- Faulty water valve (1 mentions)
User Suggested Solutions
-
Replace faulty pressure transducer
Limited-source guidance; percentages and success-rate claims are not shown
View
Sources
Data compiled from real discussions on r/appliancerepair and r/Appliances:
Community Discussions
drains as fast as it fills
Faulty pressure transducer on the control board may be the issue.
Source: Reddit r/appliancerepair
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!