Amana Washing Machine: not filling with cold water

Professional Repair Guide

What is this symptom?

If your Amana washing machine isn't filling with cold water, it may not draw any water, fill only with hot water, or fill very slowly. This issue can stem from a closed cold water supply valve, a kinked hose, or less commonly, a faulty water level pressure switch. Troubleshooting these elements can help restore normal functionality to your machine.

Urgency: Medium

Important Tips for Amana Models

  • Amana-specific guides and repair sources emphasize checking water supply valves, inlet valve screens, and common component failures like inlet valve, pressure switch, and temperature selector switch.

Possible Causes

Cold water supply valve closed or kinked hose

How to Identify: Cold water supply valve behind washer not fully open or hose bent/kinked; water flow weak when hose disconnected at wall.

Part: Cold water supply hose/valve

Low household water pressure

How to Identify: Weak water flow from cold water hose when tested directly; pressure below typical household standards.

Part: Household plumbing pressure

Faulty water level pressure switch

How to Identify: Washer stops fill prematurely or does not sense cold water fill; pressure tube may be blocked or sensor defective.

Part: Pressure switch/air tube

DIY Solutions

Check and open cold water supply valve and straighten hoses

Easy 5–10 minutes
Tools Needed: None
  1. Ensure the cold water supply valve behind the washing machine is fully turned on.
  2. Inspect the cold water supply hose for kinks or bends preventing flow.
  3. Straighten any kinks or replace the hose if damaged.
⚠️ Safety First: Turn off water supply before repositioning hoses if needed.

Clean cold water inlet valve screens

Moderate 15–30 minutes
Tools Needed: Wrench, Soft brush, Bucket
  1. Turn off water supply and unplug washer.
  2. Disconnect cold water hose from the back of washer.
  3. Inspect and gently clean the inlet valve screens with a soft brush.
  4. Reattach hose, turn water back on, and test fill.
⚠️ Safety First: Ensure washer is unplugged during disconnection.

Professional Repairs

Replace cold water inlet valve

Estimated Cost: $50 - $150

Replace temperature selector switch

Estimated Cost: $40 - $100

Check and replace water level pressure switch

Estimated Cost: $50 - $150

When to Call a Professional

Cold water inlet valve suspected defective after DIY cleaning
Electrical control or temperature selector issues suspected
Pressure switch or internal sensing components malfunctioning

Preventive Maintenance

  • Inspect and clean inlet valve screens: Clogs that restrict cold water flow
    Frequency: every 6–12 months
  • Regularly check hoses for kinks or damage: Water flow restriction
    Frequency: quarterly

Frequently Asked Questions

Why is my Amana Washing Machine not filling with cold water?
The most common causes are a closed cold water supply valve or a kinked hose.
How do I fix Amana Washing Machine not filling with cold water myself?
Check the cold water supply valve and straighten any kinks in the hose. Clean the inlet valve screens if necessary.
How much does it cost to fix not filling with cold water?
Replacing the cold water inlet valve costs between $50 - $150, while other parts range from $40 - $150.
When should I call a technician for not filling with cold water?
If you've checked the valve and hose but the issue persists, it may be time to call a technician.

References & Sources

Community Analytical Insights

Analysis based on real user discussions from appliance repair communities

Can I Fix This Myself?

75%
DIY Success Rate Difficulty: DIY

Common Issues Reported by Users

  • Clogged cold water inlet filter
  • Faulty cold water solenoid valve
  • Issues with the water supply (e.g., turned off, kinked hose)

User Suggested Solutions

  1. Check and clean the cold water inlet filter. Turn off the water supply, disconnect the hose, and remove the filter. Clean it under running water and reassemble.

  2. Test the cold water solenoid valve. Use a multimeter to check for continuity. If there is no continuity, replace the solenoid valve.

  3. Inspect the water supply line. Ensure that the cold water tap is turned on and that the hose is not kinked or blocked.

Analysis based on 1 community discussions
View Sources

Data compiled from real discussions on r/appliancerepair and r/Appliances:

  1. Amana Washing Machine Not Finishing Cycle - Cold Water Tap N...

Community Discussions

not finishing cycle, cold water tap not working

Considering replacing the control board and testing the water solenoids.

DIY View on Reddit →

Source: Reddit r/appliancerepair

User Comments (0)

Share your experience or solution below.

Be the first to comment!