Amana Washing Machine: not filling on cool/cold
What is this symptom?
Is your Amana washing machine not filling with cold water? This issue may stem from a faulty cold water inlet valve, clogged filters, or kinks in the supply hose. If your washer fills slowly or not at all during cool/cold cycles, it's important to diagnose the underlying problem to restore proper function.
Important Tips for Amana Models
- Official Amana troubleshooting emphasizes checking hoses and water supply first for fill issues
- Water inlet valves are common failure points in Amana washers leading to fill problems
Possible Causes
Cold water inlet valve solenoid failure or valve blockage
How to Identify: Cold water does not flow into the washer when the cold tap is open and the cycle is on cold; hot water may still fill normally.
Part: Water Inlet Valve (cold side solenoid)
Clogged or restricted water inlet hose filter screen
How to Identify: Water pressure to machine is low or zero despite open cold water supply; removing hoses reveals buildup at hose filter screens.
Part: Inlet hose filter screens
Kinked, damaged, or blocked cold water supply hose
How to Identify: Visual inspection shows hose bent, pinched, damaged, or blocked; correcting hose position changes water flow.
Part: Cold Water Supply Hose
Emergency flood-stop device engaged on hose
How to Identify: Hose flooding safety device may stop water entry; resetting by lowering water pressure sometimes restores flow.
Part: Emergency Stop/Flood Device
DIY Solutions
Ensure cold water supply and hoses are properly connected and open
- Confirm household cold water valve supplying washing machine is fully open.
- Inspect the cold water hose for kinks or obvious damage; re-route to eliminate bends restricting flow.
- Reconnect hose ends firmly to washer and wall taps as needed.
Clean inlet hose filter screens
- Turn off both hot and cold water supply valves.
- Place bucket or towel under hose connections.
- Unscrew cold water hose from washer and inspect the filter screens at both ends.
- Use a small brush to gently remove debris on the screens.
- Reattach hose, ensuring a snug fit, and turn water back on.
Next step
Choose the next step for not filling on cool/cold
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Water Inlet Valve
Controls the flow of hot and cold water into the appliance.
- Typical part-only price
- $25 - $60
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Water Supply Hose
Connects your home water valves to the water inlet valve on the appliance.
Model-compatible Washing Machine parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Washing Machine Cleaner Tablets
Routine tub-cleaning supplies for residue and odor control. They do not repair a mechanical, drainage, or electronic fault.
Braided Washer Inlet Hoses
A maintenance replacement option for visibly worn external fill hoses. Verify thread size, length, and hot/cold connection requirements.
Washer Drain Hose Holder
Helps secure an external drain hose at the standpipe. It does not correct an internal pump or control fault.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Professional Repairs
Replace cold water inlet valve or solenoid
Diagnose and fix internal control or pressure switch issues
When to Call a Professional
Preventive Maintenance
-
Inspect and clean inlet hose filters: Clogs that restrict water fill
Frequency: annually -
Replace old supply hoses: Hose degradation and leaks
Frequency: every 5 years
Frequently Asked Questions
Why is my Amana Washing Machine not filling on cool/cold?
How do I fix Amana Washing Machine not filling on cool/cold myself?
How much does it cost to fix not filling on cool/cold?
When should I call a technician for not filling on cool/cold?
References & Sources
Community Analytical Insights
Guidance from available sources; statistical claims are shown only for samples of at least 10 discussions
Common Issues Reported by Users
- Clogged water inlet filter
- Faulty water inlet valve
- Incorrect temperature setting or selection
User Suggested Solutions
-
Check and clean the water inlet filter. Disconnect the washing machine from power, turn off the water supply, and remove the hoses from the back. Inspect the filters inside the inlet valve for clogs and clean them thoroughly. Reattach everything and test the machine.
-
Test the water inlet valve for continuity. Unplug the machine and access the water inlet valve. Use a multimeter to check for continuity. If there is no continuity, replace the valve.
-
Verify the temperature setting. Ensure that the cycle selected is compatible with cold water filling. If necessary, reset the machine settings and try again.
Limited-source guidance; percentages and success-rate claims are not shown
View
Sources
Data compiled from real discussions on r/appliancerepair and r/Appliances:
Community Discussions
does not fill on cool/cold
Cleaned the screen on the water valve, which resolved the filling issue.
Source: Reddit r/appliancerepair
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!