Amana Washing Machine: making noise when filling
What is this symptom?
Is your Amana washing machine making unusual noises like whistling or banging while filling with water? This can indicate issues with the water inlet valve, high water pressure, or loose hoses. Identifying the cause early can prevent further damage and ensure your appliance runs smoothly.
Important Tips for Amana Models
- Amana support notes hoses that knock against the washer cabinet during fill can cause noises; secure them.
Possible Causes
Water inlet valve issues (clogged or failing)
How to Identify: Noise (squeal/whistle/rattle specifically during fill; stopping water supply stops noise
Part: Water inlet valve
High water pressure or water hammer in plumbing
How to Identify: Loud banging or hammer-like knock coinciding with fill start/stop; often outside the washer
Part: Home water supply plumbing/washing machine inlet interaction
Loose or unsecured water inlet/drain hoses
How to Identify: Rattling noise as water moves; physical vibration or movement of hoses detected
Part: Water hoses
Loose or worn internal components buzzing during fill
How to Identify: Buzzing or vibration when water flow begins; no clear inlet valve fault
Part: Internal hardware (mounts, loose screws)
DIY Solutions
Clean/Inspect Water Inlet Valve Screens
- Turn off power and water supply
- Pull machine out and disconnect inlet hoses
- Remove screen filters from water inlet valve
- Clean debris/mineral buildup from screens
- Reassemble hoses and turn on water and power
Secure Loose Water Hoses
- Turn off water supply
- Check water inlet and drain hoses for movement against cabinet
- Use zip ties or supplied strap to secure hoses so they do not vibrate
- Restore water and observe during fill
Adjust Water Pressure at Supply Valves
- Locate hot and cold water supply valves to the washer
- Slowly adjust valves slightly closed to reduce pressure
- Run a fill cycle and observe any change in noise
Next step
Choose the next step for making noise when filling
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Water Inlet Valve
Controls the flow of hot and cold water into the appliance.
- Typical part-only price
- $25 - $60
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Model-compatible Washing Machine parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Washing Machine Cleaner Tablets
Routine tub-cleaning supplies for residue and odor control. They do not repair a mechanical, drainage, or electronic fault.
Braided Washer Inlet Hoses
A maintenance replacement option for visibly worn external fill hoses. Verify thread size, length, and hot/cold connection requirements.
Washer Drain Hose Holder
Helps secure an external drain hose at the standpipe. It does not correct an internal pump or control fault.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Professional Repairs
Replace Water Inlet Valve
Plumbing Adjustments (install water hammer arrestor/reduce home water pressure)
When to Call a Professional
Preventive Maintenance
-
Clean inlet screens periodically: Mineral buildup causing fill noise
Frequency: annually -
Check and secure hoses: Hose vibration noise and abrasion
Frequency: semi-annually
Frequently Asked Questions
Why is my Amana Washing Machine making noise when filling?
How do I fix Amana Washing Machine making noise when filling myself?
How much does it cost to fix making noise when filling?
When should I call a technician for making noise when filling?
References & Sources
Community Analytical Insights
Guidance from available sources; statistical claims are shown only for samples of at least 10 discussions
Common Issues Reported by Users
- Faulty water inlet valve
- Kinked or damaged fill hoses
- Air in the water lines
User Suggested Solutions
-
Inspect and replace the water inlet valve if it's faulty. Disconnect the power and water supply, remove the valve, and install a new one. Reconnect everything and test the machine.
-
Check the fill hoses for kinks or damage. Ensure they are straight and securely connected. Replace any damaged hoses to prevent noise.
-
Purge air from the water lines by running the machine on a fill cycle without any laundry. This can help eliminate noise caused by trapped air.
Limited-source guidance; percentages and success-rate claims are not shown
View
Sources
Data compiled from real discussions on r/appliancerepair and r/Appliances:
Community Discussions
making terrible noise when filling with water
Replace the water valve if normal pressure is observed through the hoses.
Source: Reddit r/appliancerepair
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!