Amana Dryer: not stopping at cool down stage

Professional Repair Guide

What is this symptom?

Is your Amana dryer running past the cool down stage? This issue may leave clothes over-dried and can be caused by restricted airflow, a malfunctioning moisture sensor, or a faulty timer. Addressing these problems promptly can save energy and prevent further damage.

Urgency: Medium

Important Tips for Amana Models

  • Some Amana models have known issues with moisture sensors and control boards affecting cycle completion

Possible Causes

Restricted airflow and clogged vent system

How to Identify: Long run times, overheating, weak airflow at external vent, lint build‑up seen in filter/ducts

Part: Dryer vent and blower system

Malfunctioning moisture sensor

How to Identify: Dryer runs excessively even when clothes are dry; sensor bars visibly dirty or unresponsive

Part: Moisture sensor bars

Faulty timer or control board

How to Identify: Cycle does not advance or shutdown properly; timer not moving toward off

Part: Timer assembly or main control board

Defective door switch

How to Identify: Dryer does not stop even when door is opened/door latch issues

Part: Door switch

DIY Solutions

Clean lint filter and vents

Moderate 30–60 minutes
Tools Needed: vacuum with brush attachment, vent cleaning brush
  1. Remove and clean lint filter thoroughly.
  2. Disconnect dryer vent hose and clean out lint build‑up with brush and vacuum.
  3. Check and clean external vent hood and flap.
  4. Run a short cycle to test airflow improvement.
⚠️ Safety First: Ensure dryer is unplugged before disconnecting vent hose

Clean moisture sensor bars

Easy 10–20 minutes
Tools Needed: soft cloth, isopropyl alcohol
  1. Unplug dryer.
  2. Locate moisture sensor bars inside drum.
  3. Wipe sensor bars with cloth dampened with isopropyl alcohol to remove residue.
  4. Restore power and test dryer with small load.

Professional Repairs

Replace faulty control board or timer

Estimated Cost: $150–$400

Replace defective moisture sensor or door switch

Estimated Cost: $50–$150

When to Call a Professional

Dryer continues to run after basic cleaning and sensor test
No change after airflow and sensor cleaning
Control components suspected faulty

Preventive Maintenance

  • Clean lint filter: Airflow restriction that can lead to extended drying cycles
    Frequency: After every load
  • Clean vent ducts: Blockages that cause sensors to misread drying progress
    Frequency: Annually or more often if needed

Frequently Asked Questions

Why is my Amana Dryer not stopping at cool down stage?
Common causes include restricted airflow, malfunctioning moisture sensors, or faulty timers.
How do I fix Amana Dryer not stopping at cool down stage myself?
You can clean the lint filter and vents, and wipe down the moisture sensor bars.
How much does it cost to fix not stopping at cool down stage?
Professional repairs can range from $50 to $400, depending on the part that needs replacement.
When should I call a technician for not stopping at cool down stage?
If DIY solutions don't resolve the issue, or if you're unsure about repairs, it's best to consult a technician.

Community Analytical Insights

Analysis based on real user discussions from appliance repair communities

Can I Fix This Myself?

75%
DIY Success Rate Difficulty: Either

Common Issues Reported by Users

  • Faulty moisture sensor causing the dryer to incorrectly assess moisture levels
  • Defective timer or control board not signaling the dryer to stop
  • Worn out or damaged door switch preventing the dryer from stopping properly

User Suggested Solutions

  1. Inspect and clean the moisture sensor: Locate the moisture sensor, usually found near the lint filter. Clean it with a soft cloth and mild detergent to remove any residue. Test the dryer to see if it stops at the cool down stage.

  2. Check and replace the timer or control board: Unplug the dryer, access the control panel, and visually inspect for any burnt components. If defective, replace the timer or control board according to the manufacturer's instructions.

  3. Test and replace the door switch: Open the dryer door and locate the door switch. Use a multimeter to test for continuity. If there is no continuity, replace the door switch with a compatible part.

Analysis based on 1 community discussions
View Sources

Data compiled from real discussions on r/appliancerepair and r/Appliances:

  1. Amana Electric Dryer cycles not ending.

User Comments (0)

Share your experience or solution below.

Be the first to comment!