Amana Dishwasher: not completing cycle

Possible Causes

Cycle interrupted by power or door issue

How to Identify: Dishwasher stops when door is nudged; Start/Resume light behavior; display error codes; cycle resumes after resetting or closing door firmly

Part: Door latch/switch, power/control panel

Control board or electronic control glitch

How to Identify: Dishwasher becomes unresponsive, stops mid-cycle without obvious mechanical failure, persists after basic checks and resets

Part: Control board

Drainage blockage or pump issue

How to Identify: Water remains in the dishwasher when cycle stops, filter dirty, smell of stagnation or slow drainage

Part: Drain pump/filter/hose

Faulty float switch or sensors

How to Identify: Dishwasher stops after sensing abnormal water level, float doesn’t move freely or sticks

Part: Float switch/water level sensors

DIY Solutions

Reset control panel/power cycle

Easy 5-10 minutes

1. Open door and cancel current cycle if possible
2. Disconnect dishwasher from power or turn off breaker for 30–60 seconds
3. Reconnect power, close door firmly, and start a new cycle

⚠️ Safety First: Ensure power is off before touching electrical connections

Check and clean door latch and ensure proper closure

Easy 10-15 minutes

Tools Needed: Screwdriver (if needed)

1. Inspect door latch for debris or misalignment
2. Clean around latch and strike
3. Ensure door closes securely and latch engages properly

Clean filters and drain path

Moderate 15-30 minutes

Tools Needed: Warm water, Soft brush

1. Locate and remove dishwasher filter
2. Clean food debris and rinse thoroughly
3. Check drain hose for kinks and clear blockages

⚠️ Safety First: Turn off dishwasher before accessing filter area

Next step

Choose the next step for not completing cycle

Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.

Based on diagnostic data

Most relevant component to inspect

Main Control Board

The central brain of the appliance that controls all components, cycles, and timings.

Typical part-only price

$120 - $280

DIY difficulty

Medium

Estimated time

20-40 mins

Optional: enter your model number

Apply

Where can I find the model number?

Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.

Find a part that fits my model

Verify the complete model and part number on the retailer's compatibility page before ordering.

Other components that may be involved

Check these only if your diagnosis points to them.

Possible related component

Drain Pump

Pumps waste water out of the appliance during the drain cycle.

$35 - $80 · Easy · 15-30 mins

Check fit & price

Possible related component

Float Switch

Detects the maximum water level to prevent overflow and potential flooding.

$15 - $40 · Easy · 10-20 mins

Check fit & price

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.

Professional Repairs

Replace faulty control board

Estimated Cost: $150 - $400

Replace door latch/switch assembly

Estimated Cost: $50 - $150

Service drain pump or water inlet valve

Estimated Cost: $100 - $250

When to Call a Professional

Repeated mid-cycle stops after DIY checks

Visible error codes corresponding to internal faults

Strange noises from pump or motor

Water leakage or electrical issues noted

Preventive Maintenance

• Clean filters and spray arms: Drain blockages and mid-cycle stops
  Frequency: monthly
• Check door latch and seal for debris/wear: False door-open detections causing cycle interruption
  Frequency: biannually

Frequently Asked Questions

Why is my Amana Dishwasher not completing cycle?

Common causes include power interruptions, control board glitches, drainage blockages, or faulty float switches.

How do I fix Amana Dishwasher not completing cycle myself?

Try resetting the control panel, checking the door latch, and cleaning filters and the drain path.

How much does it cost to fix not completing cycle?

Professional repairs may range from $50 for a door latch to $400 for a control board replacement.

When should I call a technician for not completing cycle?

If DIY solutions fail or if the problem persists, it’s time to consult a professional technician.

References & Sources

• Amana Troubleshooting Guide (Cycle Not Advancing) Official
• Amana Product Help: Stops Mid Cycle Official

Can I Fix This Myself?

100%

DIY Success Rate Difficulty: DIY

Common Issues Reported by Users

• Clogged filter assembly (1 mentions)

User Suggested Solutions

1. Cleaning the filter assembly

   Success rate: 50.0%

Community Discussions

won't complete cycle

Cleaning the filter assembly resolved the issue.

DIY View on Reddit →

Source: Reddit r/appliancerepair