AEG Dishwasher Error iE0
⚡ Quick Answer: The AEG dishwasher error code iE0 indicates a drainage issue, often stemming from a malfunction in the flow control or diverter mechanism. Symptoms in... ✅ DIY Fixable
What Does Error iE0 Mean?
The AEG dishwasher error code iE0 indicates a drainage issue, often stemming from a malfunction in the flow control or diverter mechanism. Symptoms include the dishwasher stopping mid-cycle, displaying the error during water intake or wash start, and failure to heat water. It is crucial to check for any kinks in hoses and ensure the water supply is on. If the problem persists, internal components may need to be inspected by a technician.
Common Symptoms:
- Dishwasher stops mid‑cycle and displays iE0 on screen.
- Error appears during water intake or wash start phase.
- Unit fails to heat water or proceed with selected program (observed in community reports).
Possible Causes
- Flow control/diverter valve malfunction (medium)
How to Fix Error iE0
DIY Fix Basic checks and reset
- Turn off and unplug the dishwasher for a few minutes to attempt a reset.
- Ensure water supply is on and there are no obvious kinks in hoses.
- Restart the dishwasher and see if the fault clears.
Technician Only Inspect and diagnose flow control components
- Remove lower access panel and visually inspect the flow control/diverter valve and its sensor wiring for damage or loose connections.
- Test the flow control motor and position sensor continuity with appropriate tools.
- Replace the diverter valve or sensor assembly if out of specification.
Parts needed: Flow control/diverter valve, Associated sensor/wiring harness
- If the error persists after basic reset and checks.
- If there is water leaking from the diverter/valve area or internal components get wet.
- If you are uncomfortable accessing internal parts.
Next step
Choose the next step for iE0
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Drain Pump
Pumps waste water out of the appliance during the drain cycle.
- Typical part-only price
- $35 - $80
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other components that may be involved
Check these only if your diagnosis points to them.
Drain Hose
Carries waste water from the drain pump to your home's standpipe or sink drain.
Float Switch
Detects the maximum water level to prevent overflow and potential flooding.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Technical Specifications
| wattage | 30W |
|---|---|
| component | Drain Pump |
| resistance | 20-40 ohms |
| part_number | AEG 1240000001 |
| voltage_rating | 230V AC |
Common Questions
What does iE0 error mean on AEG dishwasher?
The iE0 error indicates a drainage issue, usually due to a malfunction in the flow control or diverter mechanism.
Can I fix AEG dishwasher iE0 error myself?
Yes, you can try basic checks like resetting the dishwasher and ensuring the water supply is on.
How much does it cost to fix iE0 error?
The estimated repair cost for the iE0 error ranges from ¥10,000 to ¥40,000, depending on parts and labor.
When should I call a technician for iE0?
Call a technician if the error persists after basic checks, if there is water leaking, or if you're uncomfortable accessing internal parts.
Data last verified: 2026-07-26
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!